Flag nipples! (aka clasps that let you wear a flag as a cape...)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A fastener for attaching a flag to clothing by providing an attachment point for the flag's grommets.
- Ocena
- 0 / 5
- Polubienia
- 10
- Pobrania
- 21
- Wydruki
- 0
- Wyświetlenia
- 564
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Costume Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Let me make one thing clear to start with, I did not approve of the name Flag Nipples. My wife and friends called them that and annoyingly, the name stuck… I much prefer “cloak clasps” but there you go…
Use case:
So anyway, what happens if:
- You want to wear a flag off your shoulders as a cape/cloak
- Your flag has grommets
- You want to attach it more securely than with safety pins or bulldog clips
- You want less risk of damaging your clothing than with safety pins or bulldog clips
- You don't want to tie something around your neck which could be annoying if the cape rides up under its own weight or could even be a choking hazard if the cape got caught.
- You don't have permanently rigid protruding nipples of your own from which you could simply hang the flag by its grommets…
Well then you need a pair of… Flag Nipples. Bet you never thought you'd end up reading that.
Basically, these are clasps that use a friction fit to attach to clothing. Once they're attached, just hook the grommets over them and there you go, you can wear your flag with pride… all day long! 🌈
How they work:
- Print 2x clasps and inserts. I found 0.25mm or 0.4mm nozzles to work perfectly fine, layer height 0.1mm or 0.2mm, but I reckon they'd work decently outside of those bounds. I also used PETG which ought to have a little more give than PLA but PLA would probably work fine too.
- Locate where on your clothing you want your cape to hang from.
- Place the clasp on the outside of your clothing, take the insert and [from the inside of your clothing] push it into the clasp. The insert should go in until it's pretty much flush with the bottom of the clasp and it should feel quite secure - you shouldn't need to force it too hard so if you are, you may need to try a thinner top.
- Once it's secure, take the flag grommet and pop it over the nipple. Again, you shouldn't need to force it too much - maybe try pushing it on at a slight angle. If still having trouble, there are some size variants or you can try editing the design file in Fusion 360.
- Strike a pose, maybe? Or naruto run perhaps (actually don't do that, it looks dangerous if you were to trip over…), idk.
Here's some videos which might explain better than I have above:
View of the back of the clasp:
Attaching the clasp to clothing:
Attaching a flag grommet:
Sizing:
I'm not actually sure if there is a standard grommet size; the couple flags I tried it on all seemed to be 12mm so I mainly designed for that. But I've also pre-exported designs targeting 11 and 13mm grommets.
I have also provided parametric files (Fusion 360). Edit the HookPayload_Diameter* (and possibly the HookPayload_Clearance) parameter and the model should be sized appropriately.
(Though please note that the model is not fully parametric, so there is probably an upper/lower limit to how much you can scale this. If you have any trouble with these, just send me a message and I'll try to help if I can.)
*Originally this was going to be more hook-y and less nipple-y so that's why they're named that…
Limitations:
It's worth noting that these were designed for the inexpensive lightweight polyester-type flags that come with thin grommet fittings. If you have a heavyweight sewn flag it's unlikely these would bear the weight. Also, these obviously won't work if the flag has something other than grommets (e.g. rope and toggle).
I've created the clearance between the insert and the clasp itself to accommodate fairly thin clothing, like a shirt or typical t-shirt. Anything thicker might mean it's tricky or impossible to get the insert in.
Also, be careful if your clothing is delicate; it's a friction fit so it is possible that these might damage some less durable clothing. You can see some creasing in the photos I uploaded but most “normal” t-shirts and shirts should be just fine - however lace or silk might be affected.
License:
I chose the CC BY-NC-SA licence so that these cannot be sold. I do not give any permission for these to be used commercially under any circumstances. However, feel free to remix to your heart's content; I've provided the design files - just note that Share Alike only permits you to distribute under a compatible license.