AGM-12B Bullpup - 3 inch High Power Model Rocket - Mk2V1
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a scaled-up version of my Bullpup Extreme model rocket
- Ocena
- 5 / 5
- Polubienia
- 36
- Pobrania
- 184
- Wydruki
- 3
- Wyświetlenia
- 841
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Noncommercial
Updates:
8/1/2024: Posted Mk2v1
10/13/2024: Added extended Nosecone coupler for a more secure fit
Introduction:
The 3-in Bullpup is an upscaled version of my Bullpup - Extreme Series rockets. It incorporates a tailcone motor retainer and a nosecone ebay to house your flight computer, GPS transmitter, or other space-faring equipment.
This design is an aggregation of years of design, engineering, and esthetics. The extreme series of rockets was intended to be easy to print, quick to assemble, and fun to fly. This rocket is simply an extension of that ideal.
It closely resembles the AGM-12B Bullpup missile, which entered service in 1964
https://en.wikipedia.org/wiki/AGM-12_Bullpup
Special Shoutout:
I have included a Camera Mount for the RunCam6 by Project Horizon. I have slightly modified this model to accommodate both Runcam6 and Runcam2 action cameras. I will have a separate remix for this mount on my profile, but I included it here for convenience
Model Files Included:
Nosecone Tip
Nosecone Base
Nosecone Coupler
Ebaysled
Nosecone plug
Fincan
Tailcone Moter Retainer
Camera Mount - Remix of Project Horizon's Runcam 6 Rocket Mount
Camera Mount Cover
Materials Needed:
¼-20 eye-bolt (or two) for the sled/plug
54mm LOC/Precision Motor Mount tubing (MMT) - 12 inches but too much is never a bad thing
15 (or more)-minute epoxy. I use QuickCure 15 and PC-7
36-48-inch parachute - 36" for grassy landing zone; larger for harder surfaces
dog barf recovery wadding(optional - or is it?)
Paint, tape, acid brush or disposable brushes, beer, brownies ;)
8-32 x 1/2-in screws (2x) for the rail buttons. M4 x 13mm equiv.
Optional:
Laminating epoxy for the internal surfaces of the nosecone (and fiberglass layup if you choose). I recommend TotalBoat
1/4-in x 20 all-thread - Optional for mounting weight to the top of the ebay
Jolly Logic Chute Release
Altimeter/Flight Computer - motor eject will still work on smaller motors. I recommend Eggtimer for those with some experience with soldering and electronics
Motor adaptors: from 54mm to 38mm or 29mm
Printing Guide:
These parts work well with PETG, though PLA+ will work too. See the print config below for part-specific recommendations. These are only recommendations, and your particular situation may call for adjustments.
If you print all the parts with either the plug or the ebay, you should be able to print all the parts on one, 1kg, spool of filament, so figure on having 2-3 on hand just in case something goes wrong. My slicer takes about 175% longer to print so I don't have exact print times yet (it's still printing). I will update my findings when I complete and fly the model.
Global Setting:
Seam: Aligned
0.2 layer height
0.4 nozzle
Adaptive Cubic infill pattern
Normal Supports
Top Z: 0.28mm
Bottom Z: 0.25mm
Base Pattern Spacing: 2mm
Part-specific Configs:
Nosecone Base:
Walls: 3
Top Shell: 3
Bottom Shell: 3
Infill: 15%
Brim Type: Mouse Ears (or inside/outside standard brim)
Brim width: 25mm
Notes: Support inner interface edge
Nosecone Tip:
Walls: 3
Top Shell: 3
Bottom Shell: 3
Infill: 15%
Brim Type: Inner and outer
Brim width: 5mm
Notes: Support inner interface edge
Nosecone Coupler/Shoulder:
Walls: 5
Top Shell: 5
Bottom Shell: 5
Infill: 100%
Brim Type: Inner and outer
Brim width: 5mm
Notes: High infill (solid) for strength
Nosecone Ebay:
Walls: 5
Top Shell: 5
Bottom Shell: 5
Infill: 100%
Brim Type: Inner and outer
Brim width: 5mm
Notes: High infill (solid) for strength
Nosecone Plug:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 100%
Brim Type: Inner and outer
Brim width: 5mm
Notes: High infill (solid) for strength
Camera Mount:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 25%
Brim Type: Inner and outer
Brim width: 5mm
Notes: Print in the upwards orientation, with the back edge flat on the build plate. Supports on the forward bulkhead. Try to keep the supports off the wall
Camera Cover:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 100%
Brim Type: Inner and outer
Brim width: 5mm
Notes: Use Variable layer height to smooth the top transition
Rail Buttons:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 100%
Brim Type: Inner and outer
Brim width: 5mm
Notes: N/A
Fincan:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 15%
Brim Type: Inner and outer
Brim width: 5mm
Notes: Support inner interface edge. Keep supports off the tailcone interface threads
Tailcone:
Walls: 5
Top Shell: 4
Bottom Shell: 4
Infill: 100%
Brim Type: Mouse Ears (or inside/outside standard brim)
Brim width: 25mm
Notes: High infill (solid) for heat resistance. You might want to print a couple, just in case.
Building Guide:
Dry Fit and Surface Prep:
Once you have all your printed parts and other materials ready, dry-fit the rocket. Everything should fit nicely, without effort. If the fit is tight, don't force it. Lightly sand the pieces with 120-400grit sandpaper.
To prepare the surface, lightly sand starting with 120 and working your way up. For external surfaces, I will usually stop at 400grit and use a sandable primer to help build up the low spots. For the interior of the Nosecone, scuffing the surface with 120 should be enough. Be sure to scuff the mating surfaces with 60-120grit to help the mechanical bond of the epoxy.
Adhesives:
There are tons of adhesives that would work for assembly. My preferences are simple epoxies like System3 and PC-7 (links above). For strength, PC-7 is very economical, but it takes a while to fully cure. System3 sets in 15mins and is usually workable within an hour.
It is tempting to use CA or Superglue, but don't. CA glue has incredible tensile strength but is garbage when it comes to shearing strength. Most of the forces on the mating surfaces for this kit are subject to shearing forces, so it’s not a good idea. Also, wood glue or white glue are not good choices because they require fiber penetration, whereas plastic has none.
Fincan - Starting with the fin can, your motor tube (MMT) should be ~12 inches starting at the top of the fincan down to the start of the threads. Dry fit your MMT into the fin can. It should be a loose fit.
Once the dry fit is complete, run one end of your shock cord down from the forward end until about 25mm (1 in) is sticking out the back. Apply a moderately thick coat of epoxy to the shock cord channel and then lay the shock cord into the channel. Apply more epoxy to the cord and to the inside of the fincan. DO NOT get epoxy on the threads. Slide the MMT up from the aft end until you are clear of the threads. Make sure the shock cord is seated in the internal channel that was modeled to accommodate it. Make sure everything is aligned and seated then set aside to dry. Clean off any excess epoxy from the fin can, retention ring, or inside of the MMT with Rubbing Alcohol.
OPTIONAL: You can also do a fiberglass layup on the fincan. You are on your own with this but be sure to share your build if you do reinforce it with fiberglass.
Body Tube:
When the fincan has set, feed the shockcord down the MMT to get it out of the way. Next, you will need ~ 16-in (406mm) of LOC 3-in body tube body tubing. Apply a medium coat of epoxy to the inside aft end of the body tube and slip it onto the fin can. Give the tube a little twist to make sure there's good coverage.
Once the epoxy for the body tube and fincan have set, you can feed the shockcord back up into the body tube and screw on the motor retainer. Next, with a piece of angled aluminum, mark a centerline down the body of the tube and extend it to the fincan. You can drill a small (~3mm) hole at the bottom of this line but do not drill through the threads or into the MMT. This will be for your aft rail button. With the tailcone on, measure up 380mm or ~15-ins from the bottom and mark that spot on your line for your forward rail button. If you are using a camera mount, this will be the general area for that too (just not on this line).
Nosecone:
First, surface prep the nosecone tip, base and coupler with 120 then 400 grit sandpaper. Be sure to get the exterior to a finish level you are happy with. You can stop at 120grit on the interior surfaces.
With some laminating epoxy, coat the inside of the tip and base. This will help with strength. Be sure to avoid the mating surfaces at this time. You can mask off for additional insurance. Once the lamination epoxy has set, apply normal epoxy to the mating surfaces fit together, pressing the two halves together tightly to avoid a join line. Clean off any squeeze-out with iso alcohol. Next, apply normal epoxy to the bottom nosecone mating surface and the couper and repeat. DO NOT get any epoxy on the threads of the coupler. Let the epoxy cure on all parts.
Ebay/Plug:
These parts are interchangeable and are primarily used for anchoring the shockcord forward end to the nosecone. There is no assembly outside of the eyebolt. The hole for the eyebolt is slightly undersized, so you can tap the hole with the threads of the eyebolt. Work the hole a few times until you are happy with the fit, then apply some epoxy to the bolt and down into the hole and assemble.
Safety Police Disclaimer:
Rocketry is a safe and rewarding hobby. With knowledge and experience, you can experience the excitement of yeeting a rocket thousands of feet into the sky. There is nothing else like it.
Having said that, you are responsible for the rockets you fly. If you build and fly one of these rockets, you should understand the NAR Safety Code and the potential risks involved with launching any rocket, especially these. They were not designed to be toys. They are real rockets that can potentially go very high and carry significant energy. This rocket is intended to be built and flown by experienced rocketeers who understand the risks and can mitigate potential issues through experience. By printing and flying this model, you do so at your own risk. You are solely liable for any unexpected results, and you agree to hold me and any manufacturer harmless of any liability. I recommend you join NAR or Tripoli, join a club, and ask lots of questions. Launching a rocket as a NAR/TRA member at a sanctioned event provides you with insurance you don't get at the park. </end of Safety Rant>