Schieberschild AV Wasser - Marker Plate for Valves
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Hinweisschild für Absperrventil Wasser ähnlich DIN 4067 Marker Plate for Water Shut-Off Valve similar to DIN 4067
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 52
- Wydruki
- 0
- Wyświetlenia
- 426
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Nach der Aufbereitung der Außenfassade am Haus fiel mir das alte schon recht heruntergekommene Hinweisschild für das Absperrventil des Wasseranschlusses auf.
Also hab ich mich mal drangesetzt und diese Modelle erstellt.
Das Schieberschild (oder Armaturenschild, oder Hinweisschild zu Straßeneinbauten, …) dient zur Kennzeichnung der Position des Absperrventils für den Wasser-Hausanschluss und ist nahezu an jedem Gebäude zu finden.
Alle die dieses Schild “verloren” haben oder durch ein optisch neueres ersetzen möchten können hier fündig werden
Die Ziffernplatten werden von hinten in das Schild eingesetzt und von der Rückenplatte an ihrer Position gehalten (wenn angeschraubt). Das Schild wird mitsamt Ziffernplatten und Rückenplatte an der Wand befestigt.
Ich habe mir große Mühe gegeben den Vorgaben der Norm DIN 4067 gerecht zu werden, werde eine Garantie hierfür aber klar ausschließen
Druck:
Gedruckt in 0,2mm Layerhöhe habe ich die Oberfläche des Schildes und der Ziffernplatten bügeln lassen um dem Original optisch näher zu kommen. Geschmackssache
Schild
Support ist hier nötig, da der Hohlraum hinter dem Schild überbrückt werden muss. Achtet bitte auf einen ausreichend hohen Z-Abstand zwischen Support und Schild. Wie auf den Fotos zu erkennen ist, habe ich das nicht getan und habe viel Zeit und Tränen benötigt um den Support wieder zu entfernen 😅
Rückenplatte
Hier hatte ich etwas Haftungssprobleme, lag aber an meinen eigenen Fehleinstellungen. Da dies kein sichtbares Teil ist, hab ich es einfach gelassen🤷
Ich würde mich sehr über eure Makes und Anregungen freuen
-----------------------------------------------
After preparing the Facade of the house, I noticed the old, rather dilapidated sign for the shut-off valve for the water connection.
So I sat down and created these models.
The Marker Plate (German Standard) is used to identify the position of the shut-off valve for the Water-House-Connection and can be found on almost every Building in Germany.
Anyone who has “lost” this Plate or would like to replace it with a newer One can find it here
The Numberplates are inserted into the Marker Plate from the Rear and held in place (when screwed on) by the Backplate. The Plate is attached to the wall along with the Numberplates and Backplate.
I have made great Efforts to meet the requirements of the german DIN 4067 Standard, but I will clearly exclude any Guarantee for this
Print:
Printed at 0.2mm layer height, I had the surface of the sign and the number plates ironed to visually get closer to the original. A matter of taste
Sign
Support is necessary here because the cavity behind the Plate must be bridged. Please ensure there is a sufficiently high Z-distance between the support and the Plate . As you can see from the photos, I didn't do this and it took a lot of Time and Tears to remove the Support 😅
Backplate
I had some liability Problems here, but it was due to my own incorrect settings. Since this isn't a visible part, I just left it 🤷
I would be very happy about your Makes and Suggestions