Reparatur-Dichtschelle DN20-26,9 - 3/4"
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Reparatur-Dichtschelle DN20-26,9 - 3/4" für Notreparatur bei Rohrbruch.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 36
- Wydruki
- 0
- Wyświetlenia
- 178
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Mechanical Parts
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Reparatur-Dichtschelle DN20-26,9 - 3/4" für Notreparatur bei Rohrbruch.
ACHTUNG !
Die Verwendung dieser Teile kann die Gefahr mit sich bringen das es zu einem erneuten Wasserschaden kommt, mit dem Download bestätigt der Empfänger / Verwender dies auf eigenes Risiko zu tun!
Ich schließe hiermit jegliche Haftung aus!
Da ich ein Älteres Haus besitze und es in solchen zu defekten Rohrleitungen kommen kann und ich neulich einem Installateur bei so einer “Notreparatur” zugesehen habe kam ich auf diese Idee.
Das Wasser konnte zu dieser Zeit nicht abgestellt werden und er hat eine ähnliche Reparatur-Dichtschelle (Seine war ein Kaufteil aus Metall) in ca. 5 Minuten angebracht und sie hält dicht.
Es sind nur 2 der hier bereitgestellten Teile erforderlich. In jedem Fall Reparatur-Dichtschelle DN20-26,9 01-Schelle Kopf
und hierzu wahlweise entweder Reparatur-Dichtschelle DN20-26,9 01-Schelle M8
oder Reparatur-Dichtschelle DN20-26,9 01-Schelle Mutter M8
bei der zweiten Variante werden dann noch 6 Stück M8 Muttern zu den in jedem Fall benötigten 6 Stück M8 x 30 Schrauben DIN 912 benötigt.
Als Dichtung ist ein Stück Gummi aus einem Fahrradschlauch geschnitten
vorgesehen 70 x 70 mm.
Anwendung:
Die beiden gewählten Teile neben der undichten Stelle des Rohres mit der Gummidichtung “lose” vormontieren und erst vor der endgültigen Montage gezielt über die undichte Stelle schieben. Dann gleichmäßig anziehen, bis es dicht ist. Vorsicht es ist nur Kunststoff.
(ich denke je nach Druckergebnis und Füllgrad maximal 12-14 Nm)
Als Material empfehle ich PC oder PETG in dieser Reihenfolge.
Auch wenn das Ergebnis der Bohrungen und Gewinde für die Schrauben etwas darunter leidet in jedem Fall stehend drucken!!!
Der Füllgrad sollte möglichst hoch gewählt werden am besten 100% aber mindestens 80%.
------------------------------------------------------------------------------
Google translates:
Repair sealing clamp DN20-26.9 - 3/4" for emergency repairs in the event of a pipe burst.
DANGER !
The use of these parts can involve the risk of further water damage. By downloading, the recipient/user confirms that they are doing this at their own risk!
I hereby exclude any liability!
Since I own an older house and can have defective pipes and I recently watched a plumber doing such an “emergency repair”, I came up with this idea.
The water could not be turned off at that time and he has a similar repair sealing clamp (his was a purchased metal part) in approx.
Installed for 5 minutes and it stays tight.
Only 2 of the parts provided here are required. In any case, repair sealing clamp DN20-26.9 01 clamp head
and optionally either repair sealing clamp DN20-26.9 01 clamp M8
or repair sealing clamp DN20-26.9 01 clamp nut M8
In the second variant, 6 M8 nuts are required in addition to the 6 M8 x 30 DIN 912 screws required in each case.
A piece of rubber is cut from a bicycle tube as a seal
intended 70 x 70 mm.
Application:
Pre-assemble the two selected parts next to the leaking area of the pipe with the rubber seal and only push them over the leaking area before final assembly. Then tighten evenly until tight. Be careful, it's just plastic.
(I think a maximum of 12-14 Nm depending on the printing result and filling level)
As a material, I recommend PC or PETG in that order.
Even if the result of the holes and threads for the screws suffers a little, in any case print standing up!!!
The filling level should be as high as possible, ideally 100% but at least 80%.