1 / 7
HOT AIR BALLOON BIRD FEEDER No glue or supports. — zdjęcie 1
1 / 7

HOT AIR BALLOON BIRD FEEDER No glue or supports.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A bird feeder in the shape of a hot air balloon. The volume of the balloon holds seeds. No supports, no glue.

Ocena
5 / 5
Polubienia
29
Pobrania
71
Wydruki
1
Wyświetlenia
827
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

The original balloon is a lovely model, but has a limited food capacity. This bird feeder takes advantage of the volume provided by the balloon itself to hold seeds.

 

BEFORE GETTING STARTED :

 

  • I recommend printing everything in ASA, for weather and UV resistance.
  • You have two options for the bottom of the feeder :

A slick perch, or a plate.

Pick your favorite one.

 

I like the perch because it's classy, and I like the plate because it can welcome more than two birds at once.

 

  • You have options regarding the middle screw :

The feeder requires a screw longer than 300mm. However, to enable all machines to produce the needed parts, I provide a 160mm long screw model, that gets printed twice and gets assembled into the final screw, as described by STEP 1.

However, I do provide a 280 mm screw, that I actually preferred using, when putting together the wide base alternative.

I just find it out of proportions if the wide base is too far bellow the balloon.

 

  • The assembly requires no glue.

(It's more fun and convenient this way)

 

ADDITIONAL SUPPLIES :

 

  • A bottle, with a smooth section, like the one in the image bellow.                                          (I personally used Schweppes bottles)
  • A length of string
  • Some nails

 

 

Assembly .

If it all sounds complicated at first, don't worry. It's very straight forward once you have all parts in hand. It took me less than five minutes to assemble mine, apart from preparing the column.

The illustrations provided bellow show the completed step they depict.

 

  • STEP 1

Grab :

  • The two 160mm long screws
  • The connector
  • The wedge

Put everything together

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 2

  • Grab the top segment holder and screw it so that a few centimeters of the axis stick out.    
  • Grab the Feeder cap and screw it in place      
  • Screw the top segment holder back until it touches the cap                                                   
  • Unscrew the cap                                                 
  • Take a piece of filament and insert it in the holes on the side of the center cylinder, so that the cap gets locked onto the screw.                                                                                    (A piece of TPU filament is best for this step since its flexible, making it easier to insert, and it wont risk snapping)                                        
  • Put the cap back on                             

(Though not accurately depicted in the image, the blue and yellow parts should be touching, and the blue should be tightened against the yellow part)

 

 

Step 3

  • Grab the interface and screw it until it gets very close from the connector.        
  • Put the fragments in place between the interface and the segments holder.  

(Flipping the whole thing upside down makes this step easier)

  • Once everything is in place, screw the interface onto the fragments while aligning everything.

It should end up looking like this, with all fragments present of course.

 

Step 4

  • Grab the base, engage the screw insert plate onto the base threads, just enough so it stays on there.                                                
  • Grab your transparent plastic, form it into a cylinder and slide the ring onto it. It ll help maintaining it in shape.                                    
  • Insert the cylinder in the space between the insert and the base.                                           
  • Grab the windows and set them in position by lifting the transparent plastic, one side at a time, inserting the window then setting the whole thing in position                               
  • Once both windows are set, screw the insert plate through the bottom plate with nails.

 

Assembling the wide base goes the same way, except that you don't need to install windows.

 

Step 5

 

  • Insert the screw through the column then into the plate threads and screw things together.

 

(While screwing, make sure that the top of the column fits into the groove of the interface.)

 

 

 

 

 

 

 

 

 

 

 

CONGRATULATIONS, YOU'RE DONE ASSEMBLING !

 

The last step is to fill it.

One drawback this feeder has is you have to fill it through the top, which is partially blocked by a bar that connects the center cylinder to the outer ring.

To address this issue, I've made a little funnel that can be screwed on top of the balloon after the cap gets removed. On my feeders, I permanently attached it to the top cap by threading the string into the hole. For sure the feeder is left with this thing on it's top. But at least I won't loose it.

 

Please share your makes, along with photos of the stunning birds that visit them !

HAPPY BIRD FEEDING  !

Tagi