Liczymy pasujące modele…
Handles for the new IKEA ALEX drawer cutouts. Popular models were seemingly designed for an older version of ALEX units, and didn't fit. These attach with some double sided tape to the drawer front.
A Gridfinity 3x3 base tray, with handles screwed to the sides. This can be used as standalone or stacked with ½ unit offset on top of stackable bins. I use them to stack double 8u height bins in the deeper drawers of my Ikea Alex units.…
Stanley measuring tape truss clamp, for 48mm truss tubes. Perfect when trimming flown trusses for live events, we've been using these for years now. Kept getting questions about these so I figured I would upload them here. Print using a…
I moved both filament sensors to the same side of my XL, so I needed to fit my 5 spools on the same side of the printer. These double rollers allow you to hang spools side by side on the side of the XL. The rollers are 75mm wide, but…
Airtag strap clip. Fits on a 30mm strap and the Airtag snaps in place. Prints well in PETG.
Purge tray for the Prusa XL with three 10x3mm magnets embedded in the part. Sticks to the underside of the steel sheet. Pause the print at Z=3.2mm to add the magnets. Recommended to print using a material with high glass temperature, such…
A Gridfinity 2x3 base tray, with handles screwed to the sides. This can be used as standalone or stacked with ½ unit offset on top of stackable bins. I use them to stack double 8u height bins in the deeper drawers of my Ikea Alex units.…
Frame for the IKEA Styrbar that replaces an ELKO RS frame. Fits the older version (see photo) as well as the newer one. Printed face-down on a Prusa Mini with 3dJake EcoPLA, Matt white. Use supports! Instructions Remove the switch cap and…
Fitting / mounting mechanism for the Olight RN120 rear bike lamp. Use the STL or STEP files to create your own mount that fits your needs.
Plastic parts for older pivot windows manufactured by SP fönster. Also fits some Elementhus pivot windows model TT. The male parts ("spanjolett", article EDF-1412013) are mirrored for left and right sides of the windows. Female parts…
Gridfinity bin for two 150mm digital calipers. With holes for 6x2mm neodymium magnets. There are now three versions: Both calipers facing same direction (v2) - works well when the bin is partially covered such as in a drawer that does not…
A remixed top panel for the EnXLosure, using a separate sheet for the top panel, and splitting the four sides into separate parts to be less susceptible to warping issues. Requires the following additional hardware: 14x M3 inserts 14x…
Wider bins that works with Patrik Kokinda's cutlery organizer . Two wider versions, one double and one triple width (120mm and 180mm exterior). Uses the original connectors. I added text modifiers in PrusaSlicer before printing, they are…
Mount for Olight RN120 which fits on a Bontrager BackRack Lightweight MIK. May fit other rear racks that utilizes 5mm holes spaced 50mm apart. Printed with supports on buildplate only. If you want to design your own mount I have also…
Top mount for Olight RN400 bike lamp. Uses the original plastic part but puts it on the top of the light instead of the bottom. Allows for mounting below handle bar and still using the “anti glare” lens feature. Hardware needed: 2x short…
Raspberry Pi Camera v3 / Zero case for Prusa XL enclosure. Camera and Pi screws into the extra holes on the enclosure frame. Case is very simple and has a lot of openings to make sure there is as much airflow as possible given the high…
Gridfinity bin for Wera 950/9 allen key set. With holes for 6x2mm neodymium magnets.
Small, portable RAK19003 case with room for RAK12500 GPS module and external LoRa antenna. Fits a 1500mAh lipo battery (50 x 35 x 8mm) such as this one. Use some double sided tape if you don't want the battery to move inside. Case is…
I found my Prusa XL to be a little bit on the noisy end, and parts of the noise I attributed to resonance coming from the side panels. Ordered some 2mm (80mil) sound deadening mat from Amazon, and cut them to size using this template.
Top mount for Rockbros RHL3000 bike lamp. Uses the original plastic part but puts it on the top of the light instead of the bottom. Allows for mounting below handle bar and still using the correct asymmetric light output. Hardware needed:…
Use neodymium magnets with countersunk holes, M3 heat inserts and short screws to attach them.
To wszystkie aktualnie dostępne wyniki.
