Liczymy pasujące modele…
The wall mount Ryobi included with their stick vac was pretty pathetic. So, I modeled this up to meet our needs. It holds all the tools that were included with the vac and keeps everything as compact as possible.
Picked up a set of the Govee RGBIC permanent outdoor lights but I'm not a big fan of the idea of using the adhesive. Partially because I don't want any residue to clean up in the future should these lights fail or loose their appeal and…
I wanted to use a low profile PCI slot to mount a 2.5" SSD in a 2U case for my Unraid server but I didn't see any manufactured nor any available to print out. So, I designed my own. I've not yet got to install it as I'll have to make time…
I whipped this up before even checking to see if some were already available. The others available are likely fine, but I figured I'd upload mine as well since I already made it. It's a tight, press on fit. I printed mine with PolyMaker…
Simple wall mount for a Govee H5179 sensor. Flat back with screw hole for a fastener or use with a command strip or some double sided tape.
Simple design I modeled up to better route my CPAP hose and give me a place to hang my mask. My original design is tailored for my headboard, but some folks expressed interest in the model. So, I've made it more universal so that you can…
Just a simple case for a Sandisk Cruzer U thumbdrive. Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Filament: Prusa Filament PLA Silver Category: Computer
The magnets used are 6mm diameter by 3mm thick. The spacing is 20mm center to center. Don't forget to get the polarity of each magnet correct. There is only 0.1mm of clearance in the design for the magnets. They slipped in perfectly for…
Simple mount to for a Meross MSG100 smart garage door opener. I added a spot on each end so that I could zip tie the cables as a strain relief mechanism.
This is the door sensor for a Chamberlain myQ smart garage door kit. Great way to add smart controls to a garage door for just $20. Could be tighter on design for sure. But for 15 minutes in fusion it works as I intended. Four 6mm x 3mm…
Simple basket I designed to drop into a Karter 1000mL beaker that I use to wash small resin prints atop a magnetic stirrer. 07-11-19: original lid was tight for me, I'd suggest scaling up a bit if you print it. I also decided to model a…
My father asked if I could design this for him as the OEM throat plate didn't set quite flush with the table. This can obviously be used as a replacement though if you've broken or lost yours. Update 11/6/19 - Added a updated .stl of the…
As shown in the pics, one of the bushings for the Milescraft base plate had failed so I set out to make a replacement. Recreated it to my liking, cut a piece of ¼" tubing which was press fit in with a little heat. Printed in ABS w/ 99…
Just a couple things I modeled up to replace parts on my boys toy lightsabers. No supports required for anything, just print them with the flat base on the bed. The blade takes a litte bit to get it worked loose, but after that it's…
This is a simple solar powered tree node that utilizes a Heltec V4 and a Meshnology 3000mAh battery pack. I actually just bought the full kit from Meshnology on Amazon sometime ago and then ultimately decided to build this. I've had this…
Just a simple container to keep my 2 year old from squeezing the pouch everywhere other than in his mouth. Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 15 Category: Containers
Wife bought a Bio Orb Halo and for whatever reason the manufacturers must think that you won't have a need for a heater or thermometer as they didn't allot for wiring. So, I simply recreated the cover in a close enough fashion and created…
This is the follow up to my Heltec V4 solar tree node. The original hangs from a rope and worked fine, but I wanted to get up above the canopy, so I redid the whole case to screw onto the top of a 1-1/2" PVC pipe. The pipe gets hoisted up…
To wszystkie aktualnie dostępne wyniki.
