Liczymy pasujące modele…
Note: All dimensions have been designed to work well with a size-and skew calibrated printer. Use the instruction further down to adapt the model if necessary. Do not force anything that does not immediately and easily fit. General…
Printed with a pause at layer 46, to fill it with some small-grained rice. Choose an infill pattern that allows you to fill it up top-to-bottom, like triangles. Print the two parts separately. You probably don't need supports for the…
Lock the fader in place if you don't need it, and entirely remove the risk of accidentally causing chaos. Tested on a DJM-S7 only. It should fit other mixers of the DJM range as well. Fader slot width: 55mm Fader knob width: 12mm
This model holds a digital angle finder protractor on your skadis wall. No supports needed to print. My Parkside angle finder is ~16mm thick and 35mm wide.
This is a 1U bracket for mounting 19'' or 10'' rack equipment under a desk/ table or vertical on wall. You will need 4 M6 nuts, 4 M6 screws and one screws to mount the brackets to the table or wall. Note: This is designed for use-cases…
Gridfinity box for the Gillette ProGlide razor and a refill pack. Base Gridifnity generated with Perplexing Labs .
Mount your beautiful sleeve covers to the wall. This version is slightly smaller and less visible from the front. The entire plate is tilted upwards 3° to ensure the sleeve leans against the wall. The plate is 10mm/1cm thick and can hold…
Hold your bins in place. Every time I used to open the bin drawer, they would go flying off to the back, making it impossible to throw anything away. Now they sit tightly in place, without it being a struggle to take out the trash. The…
Holds an X-Acto style knife and 4 refill/alternative blade boxes.
Holds my fairly heavy Beyerdynamic DT1990 PROs with 8 Magnets. Using 12 for good measure. Put one in the holes and another one on top for direct contact with the metal. Print without supports. I used ⌀ 10mm, 2mm thick, cheap magnets from…
Find the modular hand rests here: https://www.thingiverse.com/thing:2992815/files Print without supports, lying down on the flat surface. The attachments are friction-fit.
DIN-Rail mount for a single unit (18mm width). Three alternatives exist: a0: Stand without screw holes a1: Screw holes at the back, reachable when the module is mounted a2: Screw holes at the back and front, front screw is only reachable…
Raises the Yoton Y9 by around 36mm. Easily customizable height. The example pictures were printed at 2.8mm with 10% cubic infill. You'll have to put the feet on with a rotating motion and a tiny bit of force. The goal is that the feet…
Move stuff away from your desktop. Hold one height unit of any rack-mounted device. PLA wih 4-6 walls is strong enough to hold fairly heavy devices. The power strip in the photos weighs 2.34 kg / 5.16 lbs. The current design fits an IKEA…
Go grab all info you need from the original model and leave a like :)
Disclaimer This has not reached its final form, and I'm seeing this version as a proof of concept. I'm not sharing a tutorial, code, schematics or anything else just yet :) Intro This version of the motorized PS2014 uses an Arduino UNO, a…
The original model is visually and functionally amazing, but taking it off the wall to clean or replace it was a pain. I designed this version that is as easy to print and mount but also easily removed from the wall. Use water-resistant…
Prints without supports. Needs 8 mm diameter magnets; stack as many as necessary. Each magnet hole has a convenient poke-hole to remove magnets. To hold my Pixel 7a with a case, I had to use 12 magnets. For it to not move when plucking…
To wszystkie aktualnie dostępne wyniki.
