Liczymy pasujące modele…
This is a protection frame for the Yaesu FT817/818/ND series of radios, with places for rubber feet and holders for an antenna tuner. Usefull during portable/qrp work. Works with 10mm M2.5 screws and washers.
Tikka T3x bolt opening tool, for opening the bolt for maintenance. Print with 4-5 wall lines so it can handle the wear from usage.
Ham radio antenna holder, holds a glas fiber fishing rodd, to be used as a an antenna for HF radio. Fishingrod used is a 6m from swedish retailer Biltema.
This is a two part soda steam CO2 bottle holder.
This is side rails for the Yaesu FT891 HF radio, they should be used with 4 pieces of M4x10 screws with washers(smaller than 10mm diameter). The frame will protect the buttons on the front during field operations or transport. I recomend…
EFHW antenna box, to be filled with EPOXY/Resin. Uses BNC adapter and two 4mm lab-connectors.
Rifle cleaning station, holders for rifle cleaning equipment. Uses 12,5x12,5x5mm magnet or 2 x screws to mount to a wall. Fits patches that are 40mm diameter.
Transformer for end fed antennas, 49:1. Parts needed: 140-43 ferrite 100pF mica capacitor(optional, needed for higher bands) BNC chassi connector Lab power supply connector or similar 1m approx. 1mm copper wire Tested with 2530ohm dummy…
This is a wall holder for the Tapo S200B wall switch. It mounts with 2-4 screws into the wall, and the pluggs are used to cover up the screws after mounting. The Tapo switch is mounted to the holder with the supplied adhesive patch and…
Xiegu X5105 holder for field use or portable use, protects the radio and provides two stable handles to hold the radio. Connect the two parts with two M4x10/20 screw.
This is a holder for OSEC fire extinguisher 1kg powder. It fastens with two screws through 5mm screw holes. It took around 8h to print on my MK4. It should fit all fire extinguishers with a 86mm diameter.
PTT button for ham radio headset, for example Heil headsets and use with 6.3mm audio jack. To build the following is needed: 2 x 2.5mm ca 10mm screws 1 x 12,2mm button off-(on) 6.3mm audio jack 50cm data cable 8x0.25 Prints best in PETG…
This camera cover prints in three parts, the window is 50mmx1,7mm plexi/acrylic and the screws are 6 M3 screws that are 7-10mm long. Use small amount of CA glue/super glue to mount the upper and lower part. Remember to use UV stable…
This is a rain cover for RCO card readers, compatible with the same bolt pattern as the original. This is the MkII version, where holes have been adjusted on the lower part(wider).
Electronics box lid for Danfoss refrigeration compressor, replaces the old one that sometimes breaks after 20 years in a hot/humid machine room.
Vortex Viper HD 8x42 binoculars lens cap, made with TPU.
This is a mechanical QRSS keyer(very slow morse code). This can key a transmitter of lower power. Coded cogg wheel needs to be adjusted for your personal ham radio callsign. Parts needed: 3 Shafts, 5mm diameter. 46mm, 52mm and 32mm 2…
This is a handle for the LK 535 valve that is often found on the house heating unit, it sometimes break of due to stiff resistance and the hot environment where it is placed. Recomend to print this with PETG
Funnel for collecting leaking liquids, attaches to a 13mm hose in order to lead away leaking fluids to a bigger container. Funnel has six holes to be able to attach with wires. Prints without supports, fits buildplate on Prusa Mini
This is a automated dice rolling machine, it rolls three dice in a tube and reads the result with OpenCV, Python on a Raspberry Pi 5. Equipment used: Raspberry Pi 5 Pi Camera 2 DRV8825 stepper driver NEMA17 12v/0.22NM steppermotor 50mm…
Downpipe ejector 100mm with debris separator
Motor mount: RoMarine Katja motor mount for Mabuchi RS-380SH-4535(Graupner Speed 400 motor) Print with 60% infill and 4 vertical perimeters, use PETG for temperature stability Motor mount II: Reinforced motor mount for Mabuchi RS-540SH or…
For use with Yuasa np12-12, when using battery for ham radio when doing POTA. Handle is a 22mm copper pipe, if sides are not snug enough, use tape in inside to get a good fit.
Netatmo Wind meter 95x95mm pole holder
This is a replacement for the shower handle holder on Gustavberg Nautic G1/G2 shower set. Print with supports on the underside, and 100% solid, or as many vertical walls as possible. PETG or PCTG is recomended.
Yale doorman code handle cover plate, masks marks from older locking equipment installed on the door. PETG recomended.
To wszystkie aktualnie dostępne wyniki.
