P
PrintablesVinmo
Shower glass hook (metric and inch)
A simple shower glass hook. 13 sizes, for glass thicknesses from 4 - 12 mm, 3/16", 1/4", 3/8" and 1/2" .
- Pobrania
- 419
- Polubienia
- 87
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesVinmo
Bike Valve Tool
Who does not know it. The valve closure nut sticks because of tubeless milk. A small tool to clamp and open the valve nut - a must for on the go and on the trail. There is also a recess on the back with which you can remove or install the…
- Pobrania
- 211
- Polubienia
- 56
- Ocena
- 5
P
PrintablesVinmo
Backpack Strap Clip
To clamp backpack straps that are too long. 3 sizes for different strap folds. For 25 and 33 mm strap width.
- Pobrania
- 195
- Polubienia
- 31
- Ocena
- 4,5
P
PrintablesVinmo
Drawer Handle
Simple little drawer handle. 90mm wide and a hole distance of 76mm. M5 screws or 3.5 mm wood screws can be used to attach. For the M5 variant i used two M5 short thread inserts with a length of around 6mm. The diameter around 7mm. The…
- Pobrania
- 137
- Polubienia
- 20
- Ocena
- 5
P
PrintablesVinmo
Table Napkin Ring
A Tablenapkin ring for the Christmas season. Easy to print and bend. For this I use a 40mm wooden round stick, but of course anything else that has around this size will work. If necessary, I added a 40mm cylinder STL if you don't have…
- Pobrania
- 82
- Polubienia
- 33
- Ocena
- 0
P
PrintablesVinmo
PTFE tube Passtrough adapter for Ikea Lack
An adapter for the Ikea Lack table to use push fittings for 4mm PTFE tubes. You need to drill 20mm hole trough the Table. (the adapter have 19mm shaft) With the M10 and the (R) G 1/8" fittings the PTFE tube goes through, which is why the…
- Pobrania
- 57
- Polubienia
- 13
- Ocena
- 4,33
P
PrintablesVinmo
Sovol sv06 Spindle nut adapter
Because I couldn't find a suitable replacement spindle nut, I built this simple adapter. So I can install standard nuts. (TR8 x 4, with two thread starts) You only have to drill out two of the holes to 5mm if you get the standard one with…
- Pobrania
- 43
- Polubienia
- 2
- Ocena
- 5
P
PrintablesVinmo
Sovol sv06 anti backlash
Here is a suitable improvised anti backlash nut for the sovol sv06. There is not much clearance at the top of the sovol between the z-axis stops and the bridge (24mm). Finished antibacklash nuts are too long. (I didn't find any suitable)…
- Pobrania
- 39
- Polubienia
- 9
- Ocena
- 0
P
PrintablesVinmo
Sovol SV06 Dial Gauge Mount
Dial gauge holder for the sovol sv06. To check the unevenness in the bed and adjust it with spacers under the scrwes if necessary. Post-Printing Category: 3D Printing
- Pobrania
- 39
- Polubienia
- 3
- Ocena
- 0
P
PrintablesVinmo
snowflake ornament extruder sovol sv06
Outside diameter approx. 36 mm. For ⌀5mm extruder shafts with 4.5mm flattened side. I oversized the hole and the flat side a little in the file (⌀5.2mm, 4.7mm). In Cura I set the horizontal hole extension to 0.1 and it fits perfectly in…
- Pobrania
- 30
- Polubienia
- 4
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.