P
Printablesyzfr6drw
TT02 TPU Bumper
Tamiya TT02 TPU Bumper that fits Bitty Design Hyper-HR body. Printed in 95A shore TPU. Category: R/C Vehicles
- Pobrania
- 471
- Polubienia
- 34
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
Printablesyzfr6drw
Ramps for Scale 1/10th RC Car Trailer
Needed ramps to go with the excellent trailer by Bedzplane https://www.thingiverse.com/thing:3775599 The ramps use M2.5 hex caps. The bracket that mounts to the trailer are M2 hex caps and some really tiny screws that i had on hand (might…
- Pobrania
- 246
- Polubienia
- 60
- Ocena
- 0
P
Printablesyzfr6drw
Arcade1Up Cabinet HDMI Board Mount
This is to mount an aftermarket HDMI board that reuse the monitor from a Arcade1Up cabinet in the original control board location. HDMI board https://www.amazon.ca/dp/B07ZVMWPZP?ref=ppx_yo2ov_dt_b_product_details&th=1 Category: Toys & Games
- Pobrania
- 94
- Polubienia
- 9
- Ocena
- 5
P
Printablesyzfr6drw
Arrma Infraction 40mm Fan Mount with Hidden Airtag
Didn't like the fan mount clamping onto the motor so created this fan mount for 40mm fans. Added a compartment for an airtag incase it goes flying into the weeds. I used longer 4xM3 (20mm but I have to cut it shorter) and M3 washer and…
- Pobrania
- 47
- Polubienia
- 4
- Ocena
- 0
P
Printablesyzfr6drw
Arrma Infraction/Limitless/Felony Twin Antenna Receiver Platform
Using FlySky FTr10 twin antenna with my Arrma Infraction for range purposes. Needed a good way to mount the receiver and antenna. I removed the rear brake assembly already so there's room to create a platform to mount the receiver. It…
- Pobrania
- 41
- Polubienia
- 11
- Ocena
- 0
P
Printablesyzfr6drw
Nerf Aliens M41-A Pulse Rifle Brushless Cage
Impulse bought a Nerf Aliens M41A blaster and couldn't find a brushless cage so I did my own. It uses Brother Hobby Returner R6 2205 motor. Some trimming is needed on the upper shell as the brushless motor and wheels are bigger and…
- Pobrania
- 30
- Polubienia
- 6
- Ocena
- 0
P
Printablesyzfr6drw
Bittydesign Seven65 1/7 Body Light Bucket
I'm lazy and was waiting to see if anyone was going to make one...I blinked. Print it in PLA, heat it up the tabs (doesn't need to be too hot as PLA is soft around 60c) and press it up against the body so it'll conform to the body. I used…
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
P
Printablesyzfr6drw
Gyrocopter Flash 3.0 eScooter
The Flash3.0 is a Xiaomi M365 knockoff so the holes don't line up and uses different screws (M5). I also need to modify the left rack stays to clear the brake caliper. Made the hook from scratch because the one on mine is moulded onto the…
- Pobrania
- 12
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.