P
Printablesbluentity
Otrio Pieces
Pieces for the game "Otrio". Clearances tested with .4mm nozzle (.45mm nominal extrusion width) and .6mm nozzle (.675mm nominal extrusion width).
- Pobrania
- 20
- Polubienia
- 4
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
Printablesbluentity
30x30 to 20x20mm adapter
Simple adapter to mount a 20x20mm PCB on top of a 30x30mm PCB. Mostly intended for building FPV stacks. In the photo you can see that I have mounted a 20x20mm VTX on top of a 30x30mm flight controller (on top of an ESC...). This is…
- Pobrania
- 16
- Polubienia
- 2
- Ocena
- 0
P
Printablesbluentity
Aerogarden Spare Parts
Connector to link Aerogarden reservoir to main hydroponic tank. These are generally intended for resin printed and, except for the plug, would require supports for FDM.
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 5
P
Printablesbluentity
Shure MV7+ Mic Stand
Includes both a freestanding hemispherical stand and a "core" of correct dimensions for integration into other projects.
- Pobrania
- 13
- Polubienia
- 0
- Ocena
- 0
P
Printablesbluentity
31mm Tinywhoop "X" Frame
Frame for a 31mm "Tinywhoop" style drone with a 25mm AIO board (the board in the examples is the EMAX Nanohawk AIO). The major issue with this design is flexion of the "X" base affecting trim. Print it with as stiff a material as possible…
- Pobrania
- 11
- Polubienia
- 3
- Ocena
- 0
P
Printablesbluentity
Gorilla to 30mm FPV UAV Adapter
Simple adapter to allow attachment of a 30x30mm flight controller to a "gorilla mount" ESC of the type made by Team Black Sheep aka TBS. These ESCs come with a 25x25mm adapter, but not a 30x30mm. The gorilla mount uses M2 screws for the…
- Pobrania
- 7
- Polubienia
- 0
- Ocena
- 0
P
Printablesbluentity
WD1209 Temperature Probe Holder
This is a stand for the WD1209 temperature probe, although it likely fits others. I designed it for a resin printer. The holes you see in the attached image were done in the slicer to for resin flow improvement while printing and are not…
- Pobrania
- 5
- Polubienia
- 1
- Ocena
- 0
P
Printablesbluentity
M3 Flex Center Fed Dipole Holder
Holder for a center-fed dipole -- it was specifically designed for the Orqa Ghost qT antenna, which is shown in the photo. MUST be printed with a flex material, I used TPU 95A. It withstands aggressive flying (even crashes...) fine, but…
- Pobrania
- 2
- Polubienia
- 1
- Ocena
- 0
P
Printablesbluentity
Battery Holder (Ovonic 1600mAH 6S)
Basic Box for an Ovonic 1600mAH 6S LiPo battery, for use e.g. on an FPV drone. Variants for both 1 inch and half inch Velcro straps. Should be printed with TPU.
- Pobrania
- 0
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.