Liczymy pasujące modele…
This is a remix of the model https://cults3d.com/en/3d-model/architecture/statue-of-liberty-national-monument by peternak3d, which has many issues with printability. There is also a small part from https://www.thingiverse.com/thing:65869…
Source https://www.myminifactory.com/object/3d-print-mayor-the-nightmare-before-christmas-3543
Vytvořte manuálně podpěry pro šálu. Pro ostatní stačí tree support v CURA. Až tedy na bradu prince, na tu pozor, trochu se mi ulomilo. Na celkovém modelu to není poznat, ale pokud se vám to povede, vyberte pro to lepší podporu, která se…
Decimated in Blender. Checked in 3D Builder and Meshmixer for problems and holes. All good. Source is https://www.myminifactory.com/object/3d-print-female-sicilian-testa-di-moro-187853 Print Settings Printer: Kywoo3D Tycoon Rafts: No…
Remix of https://www.myminifactory.com/object/3d-print-monkey-with-skull-148312 . Higher base - 5mm, fixed holes with meshmixer. Category: Sculptures
Superb Adjustable Phone Holder, originally made and distributed on SD card with Kywoo3D printers. You can scale it as you see fit, for example around 200 % should be enough for iPads. lower paws are wide enough to hold phones even with a…
I was doing this https://www.myminifactory.com/object/3d-print-grim-reaper-159541 for a friend, who did not like the scyther, so I switched it with a raven - https://www.thingiverse.com/thing:3891587 . It is not perfect. A little bit of…
Zdroj https://www.myminifactory.com/object/3d-print-frida-kahlo-bust-7302
Edited https://creazilla.com/nodes/74126-venus-kalyppigos-3d-model Print Settings Printer: Kywoo 3D Tycoon Rafts: No Supports: Yes Infill: 15
Zdroj https://www.myminifactory.com/object/3d-print-fairy-tale-princess-30080
The sculpture is enlarged by 110 %, split into two parts I added a connection joint so there is no need to glue it. Category: Sculptures
Model https://www.myminifactory.com/object/3d-print-witch-30075 bez podstavce. Mám rád modely, kde podpory jsou pouze z tiskové plochy. Lze to namodelovat v CURA tak, ze si manuálně zvolíte podpěry pro vše co by se jinak tisklo “ve…
Vytisknuto pomocí Kywoo 3d, REGSHARE PLA, 0.4mm, detail 0.12mm.
Autor https://cults3d.com/en/3d-model/art/voodoo-sorcerer.
Model od https://www.myminifactory.com/object/3d-print-michelangelo-s-david-in-florence-italy-2052. Dejte si pozor na podpěry, hlavně na loket.
La Calavera Catrina had its origin as a zinc etching created by the Mexican printmaker and lithographer José Guadalupe Posada (1852–1913). The image is usually dated c. 1910-12. Its first certain publication date is 1913 when it appeared…
No support is needed.
Blades without supports, because the original ones are part of the print and hard near to no way to remove them. These you print with prusaslicer supports and it works fine afterward.
Made for https://www.printables.com/cs/model/854712-modern-spiral-planter-with-holes-shorter-and-small
No need for any support. But I use brim for the fast loaders. Brim type - Outer brim only Brim width - 2mm is enough Brim separation gap - 0,3mm The brim separation gap still helps with stability and it is easily removed. Also, I use 101%…
With the unchanged doll, I had a problem with ponytails. They keep falling off during printing even with support. So I made this version. I admit it is amateurish, made only with the help of Windows 3D Builder… but hey, it works. So I cut…
I was disappointed to learn that this model is hollow. I filled the bottom, filled one tip of the wing (amateurish work I admit), and made it solid.
Žeton do nákupního vozíku - 10Kč. Odpovídá skutečné minci. Vyzkoušeno v Lidlu, Penny, Trefa/Terno, Albert. Můžete zkusit i: 20Kč žeton 10Kč vytažitelný žeton 20Kč vytažitelný žeton
Model potřebuje podpory. Bohužel, nepovedlo se mi, aby se model správně vytiskl s pouze tree podpěrami CURA - upadnou konce křídel a chodidlo Amora.
No change https://www.myminifactory.com/object/3d-print-before-the-contest-116764 Print Settings Printer: Kywoo 3D Tycoon Rafts: No Supports: Yes Infill: 15
Basic sitting cat. Two models, one more basic and the other with more doodles on it. No support needed.
I remixed it to fit cars from the weekly magazine "Slavná auta".
To wszystkie aktualnie dostępne wyniki.
