Wszystkie modele

Tamper funnel Breville

Aufsatztrichter für den Siebträger der Breville Prima Latte II

simple fridge magnet - magnet inside!

This is a very simple refrigerator magnet. The magnet is in the part so that no glue is needed. Just stop the print, insert the magnet and proceed. The bag has a diameter of 10.3mm and a height of 6mm so many different magnets can be used.

Formatschablone Briefe deutsche Post

German, because its for the german post. Mit dieser Schablone können Briefe einfach vermessen werden um sie richtig zu frankieren. Ich habe die Schablone nach Beispiel der original Schablone der Post gezeichnet (Formatschablone Brief…

Parametric Condom Dispenser 50x70

angle calibration test

i made this model to check the dimensions and the angles of my printer. the 3 axes show the direction and the length. the angles can be checked inside and outside

charging station Ticwatch E3

This is a charging station for the ticwatch e3 to match this charger , which is larger than the original

Display for 'Hot End Educational Model'

This is a display i made for the ‘Hot End Educational Model’ https://www.printables.com/de/model/319366-hot-end-educational-model CAUTION! THE HOTEND MODEL I USED FOR THIS WAS SCALED DOWN TO 60% Im sure you can scale the Display up to fit…

Tamper Stand (61mm) for Breville

Temper Stand for Breville Prima Latte II about 61mm inner Diameter

Girl with flowers Hueforge

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Don't scale the Z size Filaments Used: PLA yourdroid Black Transmission Distance: 0.3 PLA yourdroid dark Gray Transmission Distance: 2.5 PLA yourdroid White…

Maine Coon Cat Hueforge

Here you can see a picture i took of my Maine Coon Cat called “dieKloi” This was my fist try of the hueforge software, so i hope you like it. Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used:…

kindle e-reader tablet device holder

This is a very simple part i made to holde my e-reader (Kindle 10th gen). This thing should work for every device up to a thickness of 9mm. I recommend printing it on the side as seen on the picture so you dont need supports. Just print…

Hueforge Old Man Window

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA yourDroid Basic Black Transmission Distance: 0.3 PLA yourDroid High Speed Dark Gray Transmission Distance: 2.5 PLA yourDroid silver…

Bottle crate 250ml 9x stackable

This is a bottle crate I designed to organize the milk bottles for my twins. It can hold up to 250ml bottles. (All bottles up to 65mm diameter and 145mm high.) If they are higher, you can't stack the crate anymore). Most of the time, the…

Skadis spoolholder - T-Clips - left & right

I designed this simple spoolholder for the few spools that wont fit the AMS lite. (It can be used without an AMS of course) The spool carrier can be mounted on the left or on the right side, no need for extra parts. You will need a M4x16…

Filament drying hood

Hey there, Recently, I had some trouble with wet filament, but I didn't want to buy a dryer as most of my filament doesn't last long enough to get wet :D However, to dry some of the rolls once in a while, I made a drying hood to dry the…

Locking screw master spool for refills

Hi, I've seen a lot of burst refill spools recently. I wanted to avoid this with my first refill and modified a multi-spool by inserting 3 holes for locking screws. (I usually only use one screw though) As with most other solutions, the…

cable chain direction changer 90 degree

I wanted to change the direction of the cable chain of my printer. the guide has a small slot so that the cables do not have to be loosened. there are holes for m3 screws with a distance of 8mm The two elements are rotatably mounted so…

Holder for Dahmit garage door opener

You can slide the opener into the printed part and attach a paper clip to hold it wherever you want. Since only the upper button has a function, I have covered all the others, so you can open the door without looking.

safety box for brennstuhl eco-line comfort switch plus

This is a small box i made to keep the comfort switch from accidentally turning off. the lid is held on by 2 m4 screws.

cable guide for brennstuhl eco-line comfort switch plus

This is a cable guide i made especialy to fit the brennstuhl eco-line comfort switch plus power strip. Inner diameter 70mm (outer dia hole 76mm / outer dia complete 96mm)