P
PrintablesHans Schulz
Fallout 4 X01 Power Armor repaired
The X01 Power armor from here: https://www.thingiverse.com/thing:1284097 Repaired using MeshLab and Microsofts Repair service. Category: Creatures
- Pobrania
- 4348
- Polubienia
- 420
- Ocena
- 4,56
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesHans Schulz
Floating tablet wall mount with charger support
A wallmount for tablets thats invisible when viewed straight on, holding the tablet 5mm from the wall. Designed for these adhesive strips: tesa Powerstrips Large . Should fit almost any tablet and is easily removable. The wall plate for…
- Pobrania
- 1966
- Polubienia
- 229
- Ocena
- 5
P
PrintablesHans Schulz
Bob Rock
Figure from https://www.prusaprinters.org/prints/93629-mini-bob-ross/comments Head from https://www.prusaprinters.org/prints/110282-roctopus
- Pobrania
- 694
- Polubienia
- 92
- Ocena
- 5
P
PrintablesHans Schulz
Fujitsu Primergy TX1330 M1 2.5" HDD Caddy
Hotswap 2.5" HDD/SSD caddy for old Fujitsu Primergy servers. Fits as a replacement for A3C40058356, see compatibility section for servers. Fits drives up to 12.5mm, however airflow might be an issue. You can use the metal piece from blank…
- Pobrania
- 347
- Polubienia
- 15
- Ocena
- 5
P
PrintablesHans Schulz
IBM System x3650 M4 2.5" Tray
Compatible for (at least) these IBM servers: X3550 M4 X3630 M4 X3650 M4 X3850 X5 X3950 X5 Fits 2.5" HDDs and SSDs with a maximum height of 15mm. Included is a version that requires (countersunk) screws and a screw-less one that clips into…
- Pobrania
- 293
- Polubienia
- 20
- Ocena
- 5
P
PrintablesHans Schulz
AZ-5 Cherry MX Keycap
Cherry MX Keycap for shutting down your RBMK reactor. Might cause prompt criticality though.
- Pobrania
- 183
- Polubienia
- 29
- Ocena
- 3
P
PrintablesHans Schulz
PI-kvm v2 case with optional oled display and 20mm fan
This is a case for the PI-kvm v2 (Raspberry PI 4) with HDMI to CSI converter. It is based on this case, from which you need to choose and print the bottom half of the case: https://www.thingiverse.com/thing:3723561 This exact HDMI to CSI…
- Pobrania
- 140
- Polubienia
- 15
- Ocena
- 5
P
PrintablesHans Schulz
Keystone Faceplate 80mm
A keystone faceplate with 80x80mm dimensions as commonly found in Europe. Angled so the keystone fits inside shallow wall boxes. Keystone fit optimized for Telegärtner AMJ-Modul K, but should also fit most other keystones. Category:…
- Pobrania
- 115
- Polubienia
- 11
- Ocena
- 0
P
PrintablesHans Schulz
Xiaomi Mija Handheld Vacuum Connector
This is a model of the connector part of Xiaomi Mija handheld vacuum cleaner accessories. It can be used to create custom ones. The push-button part that locks the connector in place is designed to be compliant enough to not require a…
- Pobrania
- 94
- Polubienia
- 25
- Ocena
- 5
P
PrintablesHans Schulz
Razer Junglecat case for Galaxy Note 10+
A case for the Samsung Galaxy Note 10+ with mounts for the Razer Junglecat controllers. The basic case is taken from https://www.thingiverse.com/thing:3935706/files and the endpiece is modified with the Junglecat mount from…
- Pobrania
- 94
- Polubienia
- 6
- Ocena
- 0
P
PrintablesHans Schulz
Rugged Bitset Box for 75mm Bits
You need 6 M3x30 screws and 18 6x3mm magnets. The Hikoki box is horribly flimsy and broke off all plastic tabs when dropped from a table. So I made this to keep the bits from now on.
- Pobrania
- 88
- Polubienia
- 19
- Ocena
- 0
P
PrintablesHans Schulz
Lenovo P1 Gen3 vertical stand
A vertical laptop stand for the Lenovo P1 Gen3
- Pobrania
- 70
- Polubienia
- 7
- Ocena
- 5
P
PrintablesHans Schulz
U.2 to M.2 adapter board case
I've bought this board to adapt an M.2 SSD to a U.2 Cable: https://www.amazon.de/gp/product/B072BXHQ4J It was by far the cheapest board with Prime delivery, but it had no case, it was just the bare PCB. So I made one myself! The PCB is…
- Pobrania
- 27
- Polubienia
- 2
- Ocena
- 0
P
PrintablesHans Schulz
Fan duct for E3D Hotend with Gregs reloaded on Mendel90
This shroud fits NumberSix's X-Carriage Fan Mod , the Greg's Wade reloaded extruder (Mirrored JHead version), RalphHiltons Part-cooling fan and the E3D v6 Hotend. The fan holes are 2.5mm to tap an M3 thread into. The hole at the top…
- Pobrania
- 10
- Polubienia
- 0
- Ocena
- 0
P
PrintablesHans Schulz
Fan duct for E3D Hotend on Mendel90
This shroud fits NumberSix's X-Carriage Fan Mod , the standard Mendel90 wades extruder , RalphHiltons part-cooling fan and the E3D v6 hotend. I've made another version for the Greg's Wade reloaded extruder :…
- Pobrania
- 8
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.