Liczymy pasujące modele…
Moon and stars to print with glow filament. Use double-sided tape to stick to the surface you want. You can adjust the size in the slizer print with 0.2 layer height
Little boxes with lids. 20cm x 2cm x 2cm (for ~ 45g silica gel) 10cm x 10cm x 2cm (for ~ 120g silica gel) 10cm x 3cm x 2,2cm (for ~ 40g silica gel) 3cm x 3cm x 2cm (for ~ 10g silica gel) 1mm opening
Floating fish-food "holder"
Messerteller für den Navimow i series. (getestet auf einem i105e, sollte auch für den i108e passen) 6 Klingen und 20cm Schnittbreite (original hat 3 Klingen und 18cm Schnittbreite) Benötigt werden neben den Klingen und den Schrauben nur…
This is a open frame chassis for Raspberry Pi 4 with 2x 2.5" HDDs/SSDs. You can mount drives with a height of 15 mm. The holes in the Raspberry have a diameter of 2,7mm. Therefore i drilled them to 3mm. BOM: 4x 20mm M3 screw (pi mount) 4x…
A spool holder for filament-spools on a flat surface. It is designed to only use one file. BOM (for two holders / one spool): 4x 608ZZ bearing 4x M3 screw 12mm 4x M3 nut
A simple holder for a xacto knife. It is designed as safe as possible, so it won't open carrying around. Be careful not to cut yourself :) Just pull the little protection ("child safety lock") down while extending the knife. IMPORTANT:…
Simple stand for light bulb. It is designed for an e27 socket / bulbholder with 40mm in outer diameter.
Tiny holder for female XT60.
Flexible Halterung für die TP-Link Tapo c200 Kamera. Die zwei Teile können in der Höhe flexibel zusammen geschraubt werden. Für einen stabileren Halt kann der Fuß nochmal von hinten angeschraubt werden.
Adpaterplatte für die Unifi Instant Kamera. Der Winkel beträgt 30°
Simple holder for a humidity sensor. You can install the sensor from above. As there are two versions of the sensor I've made two versions of the holder. The small holder is for sensors with 6 holes in the back. The large holder is for…
12V Bosch Akku Halterung für die Honeycomb Storage Wall.
A small holder for Aqara Motion Sensors. It has a hole for M5 screws. You can also use doublesided-tape to mount it.
Mini drill press for eMotor with 35mm diameter. I have used: 2x M8 rods (12 cm) for the stand. 1x M6 screw (70 mm) for the axis. 1x M6 screw (50mm) for the handle. 6x M8 nuts 2x M6 washers 4x M6 nuts 1x 9mm spring M3 Self-locking Nuts for…
Gitter für Laichkästen. Maße des Gitters: 14,94cm x 93cm Zwei Versionen: 2mm und 2.5mm Breite zum “Durchfallen” der Babys Update: V2 enthält einen Griff in der Mitte zum leichteren herausheben. Tipp: 100% Infill, sonst treibt es oben.
Box zum Aufbewahren von bis zu 6 Bits. Diese können auch außen eingesteckt werden, so dass die Box selbst als Schraubenzieher verwendet werden kann.
Tinmorry cardboard filament spool ZZ608 bearing adapter with 54.3 mm diameter. For a better installation turn the adapter clockwise. V2: more easy bearing installation
extends the lenght of a CR123A battery to the lenght of a CR17450 battery
OpenDTU ESP32 DEVKIT v4 Case with E49-900M20S for OpenDTU. Holes for screws in the back of the base: 3,4mm diameter and 31,5mm apart. One antenna is for WiFi and the other one is for CMT2300A. For the mount on a din rail I used Voron…
Geeetech spool adapter 75mm to 608ZZ bearing. Adapter has a diameter of 76mm for a tight fit. Print it with PETG so it is flexibel enough.
Masterspool for refill filament. Spooldiameter: (inside) 101.5mm x 45mm, (outside) 200mm It is designed to fit the refills from Das Filament. The spool can be used standig or with 608ZZ bearings. BOM: 3x M3 screws (~ 10mm) 3x M3 nuts…
Aufhänger für eine Rolle Klopapier
M8 threaded rod holder for M3 screws. Update: Added a shorter version if you need more space in the box.
Mount for unifi instant camera on a 20mm tube like a curtain rail. You need M3 screws.
Prusa Einsy door with 50mm fan mount for MK3S. I have used a Noisblocker XS1 - 50x50x10 mm
mobile fume extractor with 18650 battery and wemos battery shield. you can add one ore two filters.
Base for dehumitifier so the silica gel pack is 1cm above the surface. Size 15cm x 8cm x 1cm Print it with no top and no bottom layers so you can use the infill as air-passage. Update: V2 is bigger and more stable (16cm x 10cm x 1cm)
To wszystkie aktualnie dostępne wyniki.
