Liczymy pasujące modele…
Little assistants to help align stuff on the PROXXON MF70 micro mill (and presumably the standalone X-Y table by the same manufacturer). The slot is 6mm and the hole 6mm. UPDATE 29.3.2015: I made one out of aluminium. I used a 3mm end…
This is a remix of my previous remix of laird's watch strap and Lindsay Fowler's buckle. I added a latch and I used a piece of 1.75mm filament for the pin on the buckle. I have clipped my 20mm wide strap to 18mm. It's still 1mm thin. I…
Wharfedale loudpanels had a broken spring clip so I designed a replacement. The idea is to fit into the cavity with a m3 screw to provide leverage instead of the original spring (which was lost). This was printed in PLA 0.05mm layer…
Here is my remix of nathanb87's (original here: https://www.thingiverse.com/thing:6359668 ) very good Tonka wheel for the Dump Truck. The tread resembles the 970 wheel tread quite well. I could finally replace the broken and missing rear…
This is a remix of Sony Walkman TPS-L2 Display Stand by RexWolf6724 on Thingiverse: https://www.thingiverse.com/thing:6630642 I only kept the front logo part and built the rest myself. I also generated the inlayed text portion from…
Hurt my toe. Designed a cast for it. Length: 50mm Inner dia: 18mm Outer dia minor: 20mm major: 22mm Holes for air circulation and added some beams for strength. Inspired by: http://www.thingiverse.com/thing:387792 UPDATE: Printed this at…
I needed a new float chamber gasket for my Datsun 120Y (B210). The previous one had deteriorated too much and it was hand cut anyway so it had tears and poor holes for various jets etc. This new gasket was made by scanning the carb on a…
Two 40-60 mm fan adapters. Height: 26 mm Screw holes are 4 mm to make it easier to get the screws to fit even though fan screws are 3 mm. One straight and one with a 45 mm twist at one end in case this is something you might need. I…
This is an electronics tray and bulkheads for the BlueRobotics 6" ROV (149 cm inner diameter of cylinder). The Bulkheads are modified from the ones supplied by the BlueRobotics website for the 4" model. NOTE: I was unable to attribute…
The wipers crapped out on me one rainy day and I found out the plastic cap that secures the ball joint was too loose to hold the linkage in place anymore. Car is a Datsun 120Y (B210) 1975 but I have a feeling that these caps might fit…
This thing was made with Tinkercad. Work keyboard was broken. Let's see if a new one can be printed. I renamed and sliced the file at 0.10mm layer height. Should work ok. Use supports. The original foot includes a small rubber pad in the…
Remixed from erdinger's http://www.thingiverse.com/thing:151185 Proxxon stepper motor mounts. I had some nema 23 steppers so, I wanted to hook them up to my Proxxon mf 70 micro mill. I also remixed the coupler since my motors had a small…
Some plants need very occasional watering. Especially during the winter time it is not necessary to water house plants frequently. Once a week or less will be enough. This of course depends on the plant and climate. What generally happens…
This is a two piece print for a dust cover for the tape player part of the Bang & Olufsen BeoSound Ouverture system. I have printed this in a generic translucent PLA and black prusament. The logo is (NOT MINE) : Bang And Olufsen B&O Badge…
This is a living hinge printed in TPU (Flexfill 98A). I have used this in some of my other designs ( https://www.thingiverse.com/thing:2867440 ) and have full confidence that the TPU is strong enough and durable enough as a hinge…
Base and top Holding clamps for Blue Robotics ROV six inch 6" aluminium watertight enclosure. These clamps are intended for use with 163,9 mm outer diameter tubes. Two versions: One for 3d printing, with rounded features, indentations for…
This is an add on or upgrade or bodge to FoodieHao's quad watch winder that can be found on Cults3d site. https://cults3d.com/en/3d-model/jewelry/quad-watch-winder The benefit of this design comapred to ones that can be found on this site…
Remix of lucas_sp12 's Samsung S24 TPU Case With Text Don't Panic Written In Large friendly Letters On It's Back I added fillets to the edge of the case and a strip over the side buttons and supports, which need to be clipped off before…
This thing is a front mask with throughput for a round cable (24,5mm) for the Sommer Cable Stagebox 32 Channel MKII. The second file is half of the cable strain relief system. Should be a snug fit. It was made in a hurry for a pal who was…
Small foot for mounting pcbs. The foot is roughly 1x1x1 cm. The top of the foot has an indentation with a radius. I thought I made the mounting hole 4mm but I needed to drill the hole to accept the 4mm screws I had. Pics show how the…
A clip to hold schuko standard extension socket to an Ikea Ivar shelf ladder section. The relevant measurements are slotA clip to hold schuko standard extension socket to an Ikea Ivar shelf ladder section. The relevant measurements are:…
This is my model of a replacement door for the Schleich pickup truck. Mirroring should create the other side. I now know that an earlier model for this door exists on printables. However, my model is completely original. I have so far…
This is my model of a replacement rear door for the Schleich pickup truck. I have so far made test prints shown in the pics with 0.30 mm line thickness. Pictures show this printed in white.
This is a quick and dirty concept for the finger claws that enables them to be hot glued onto gloves with their tips cut off. Just the left side. I don't recommend printing this model. It is just to illustrate the idea. I don't have the…
I needed a fan for my hotend and had left the matter for too long. I had started to get really bad prints due to heat creeping up the hotend and clogging the filament feed. This is a quick and dirty 40 mm fan duct with bracket for my…
This is my model of a replacement door for the Schleich pickup truck. Mirroring this will not completely create the other side. However, the hinges should be at the same height so should provide a starting point, should you need to…
To wszystkie aktualnie dostępne wyniki.
