P
Printablessupjj
fidget soft cone
softer edge cone fidget model
- Pobrania
- 1653
- Polubienia
- 75
- Ocena
- 3,5
Wszystkie modele
Liczymy pasujące modele…
P
Printablessupjj
fidget droplet
If you print the modeled support version I would suggest using finger nail cutter to remove whatever is left on the bottom of the model. The curved cutting edge did a better job than my flush cutters.
- Pobrania
- 159
- Polubienia
- 22
- Ocena
- 0
P
Printablessupjj
rotary phone fidget
I used Archimedean chords for top surface and cross zag 45 infill when assembling the spring will need to be loaded by rotating it on the center mount peg enough to return the rotary to its base position. V2 is much smoother and should…
- Pobrania
- 117
- Polubienia
- 37
- Ocena
- 0
P
Printablessupjj
51mm portafilter funnel
I printed this in ABS with the large funnel side facing down on the build plate. designed for my KitchenAid KCG0702CS Burr Coffee Grinder which has a huge outlet, the funnel can be smaller by follow below instructions Important read below…
- Pobrania
- 87
- Polubienia
- 5
- Ocena
- 5
P
Printablessupjj
Qidi Q1 nozzle brush wiper
printable nozzle wipe replacement printed in ASA parts needed 2 X m2 screw with nuts of at least 10mm 2 X m2.5 nuts for threading in original pins optional : 1 m2 screw with nut of 16-18 mm (center fastener)
- Pobrania
- 82
- Polubienia
- 21
- Ocena
- 5
P
Printablessupjj
51mm Portafilter funnel
easy dump dose of ground espresso ready for tamping. My tamper fits perfectly through the funnel so all grounds go where they should with no mess. I found it best to print the model with the open funnel part down facing the print bed. I…
- Pobrania
- 51
- Polubienia
- 2
- Ocena
- 0
P
Printablessupjj
Goodnature A24 compatible Trap stand hood
I had an issue with a curious squirrel and the goodnature a24 trap so I designed a hood for the stand that constrains access to the strike zone and will hopefully prevent any non pest (target) animals from getting into trouble with the…
- Pobrania
- 43
- Polubienia
- 5
- Ocena
- 0
P
Printablessupjj
BTT eddy mount Qidi Q1 Pro
new version that is easier to get mounting nut into place
- Pobrania
- 40
- Polubienia
- 8
- Ocena
- 5
P
Printablessupjj
51mm espresso portafilter loading station
A 54mm espresso portafilter loading station. Keeps the mess of loading your espresso portafilter, confined and easy to clean up.
- Pobrania
- 38
- Polubienia
- 3
- Ocena
- 0
P
Printablessupjj
mace
Mace model cloning of spike model 24 times is needed in the slicer when printing cloning link model depends on needed length by multiples of 2 (so 10 total for 5 complete links) The model with prefix of S_ can be scaled to make larger…
- Pobrania
- 35
- Polubienia
- 4
- Ocena
- 0
P
Printablessupjj
skinny eddy
an enclosure for btt eddy it has allowed me to recover about 6mm of bed mesh scanning room Depending on the mount points location this may be helpful to others ABS, ASA or other heat resistant filament is required
- Pobrania
- 32
- Polubienia
- 7
- Ocena
- 0
P
Printablessupjj
Qidi Q1 Pro Eddy mount
BTT Eddy mount for Qidi Q1 Pro WARNING! It is vital that the 18mm screws that come with the Big Tree Tech Eddy are used with this mount. Longer screws will bottom out (top out in this case) and cause carriage assembly issues when…
- Pobrania
- 28
- Polubienia
- 11
- Ocena
- 0
P
Printablessupjj
Qidi Q1 Beacon/ Cartographer mount
Qidi Q1 Pro mount for Beacon or Cartographer bed probe BOM: IMPORTANT! 2X M3 12mm or 14mm for replacing the adapter stock mounting screws thanks to @Rob_3446552 for pointing this out 2 x M2.5 25mm machine screws and nuts (I used socket…
- Pobrania
- 21
- Polubienia
- 4
- Ocena
- 0
P
Printablessupjj
PIP hinged headphone hanger
I don't recommend using support as it will most likely interfere with the hinge So it is ok to ignore any slicer warnings about support generation. There is modelled support that will hold the model with the axis of the hinge in the Z…
- Pobrania
- 20
- Polubienia
- 1
- Ocena
- 0
P
Printablessupjj
goodnature a24 compatible trap stand hood
I had an issue with a curious squirrel and the goodnature a24 trap so I designed a hood for the stand that will hopefully prevent any non pest (target) animals from getting into trouble with the trap by constraining access to the strike…
- Pobrania
- 20
- Polubienia
- 4
- Ocena
- 0
P
Printablessupjj
Qidi Q1 filter box
exhaust fan port filter box for Qidi Q1. I used 25mm screws for mounting the plate to the back of the printer. 8X M3 10mm machine screws and nuts secure the rest of the assembly, the remaining joins are held together by the angled edges…
- Pobrania
- 16
- Polubienia
- 3
- Ocena
- 0
P
Printablessupjj
fidget spinning top
If printing the modeled support version I would suggest using finger nail cutter to remove whatever support material is left on the model. The curved cutting edge did a better job than my flush cutters.
- Pobrania
- 15
- Polubienia
- 7
- Ocena
- 0
P
Printablessupjj
51mm locking portafilter funnel
No mess locking funnel that helps guide espresso coffee when filling a portafilter
- Pobrania
- 15
- Polubienia
- 3
- Ocena
- 0
P
Printablessupjj
fox 36 fork compatible volume spacer
Volume spacers for Fox 36 fork I printed with PLA 4 walls and 25% cubic infill It does require support to be enabled and some cleanup post printing stack volumes below 10cc true volume 10000.761 mm^3 5cc true volume 5000.253 mm^3
- Pobrania
- 12
- Polubienia
- 0
- Ocena
- 0
P
Printablessupjj
75% Keebio Sinc tilting tenting enclosure
Keebio Sinc tilt /tent design. All variant of right half are viable with the drop in (removable) arrow key spacer and the encoder drop in mount/cover. The left half is non macro. I used 10mm hex M2.5 standoffs for all mount points along…
- Pobrania
- 9
- Polubienia
- 2
- Ocena
- 0
P
Printablessupjj
fidget skew bearing
I printed it with PLA with no support or brim
- Pobrania
- 9
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.