Liczymy pasujące modele…
10mm pieces of 3030, based on Misumi's extrusions with some different hole layouts. I don't think infill or walls particularly matter because the thin parts will stay as they are. Print Settings Printer Brand: Monoprice Printer: Maker…
Eeyore straw topper. Print Settings Printer: Corexy Rafts: No Supports: Doesn't Matter Resolution: 200 Infill: 15 Filament: ? PETG Purple Category: Other
Model is fairly large. To print on my 220x220ish printer I had to set this at 45 and turn off skirt.
2 cases for the OV3660 3MP camera board/module with the small lens. Probably fits other board of the same form factor but I can't guarantee as I only have the ov3660. Minimal case is as small as possible and only includes a hole for the…
Parametric hex sockets. Turning on add_rounds_tb or add_rounds_inner slows down rendering & openscad in general. Used with the NASA wrench with both in pla the ratchet starts skipping before the 3/8in socket stl breaks.
Odroid c1+/c2 case. Now uses m2 screws and has optional 40mm fan mount. There are 2 different bottoms, the thicker one is increased to 2mm (original is 1.5mm). There are 6 top variants, fan/no fan and original, small, and no GPIO cut out.…
SCAD customizable furniture riser Adding the center hole decreases print time depending on height & depending on print settings should increase load capacity if using hollow legs. Setting whole_round >0 with high $fn will take a while to…
Animal crossing gyroid with game slots inside When printed my top was not 100% straight so I included a rotated top version that is in 2 parts. Mine was roughly 16 deg off. Note: first version had lid thread mirrored, should be fixed now…
Handle to replace the thumb side of a pair of orange handled Fiskars scissors I broke. Uses the old screw. Supports are required. Added OpenSCAD version with rounded edges. Re-rendering takes a rather long time due to complex minkowski…
Handle and sheath for the blade of a folding credit card knife. Requires 3 M4x6 screws and 3 M4 nuts. I had to heat up the nuts to get them to go into the one I printed so I enlarged the nut holes. This was done by tracing a picture and…
Removed some top tabs for simplicity & moved tab to center Category: Electronics
Test tab moved to center where my blocks have it, removed some of the upper clip things for simplicity, added screw holes. Category: Electronics
Replacement for a Traveler's Club suitcase handle. Uses original hardware. Slightly narrower than the original but it works. There are 2 versions of the handle: V1 is what I used, it doesn't go deep enough in the telescoping part and the…
Simple psu mount for meanwell 200 or similar power supplies. Requires 2 m4x6 per bar Category: Electronics
Set of adapters to fit in an 18650 compatible Li-ion charger. Put M5 screws in the top and bottom and you can use alligator clips or other wires to charge lipos or other things that don't fit. The normal model is 18*65 not including the…
Replacement for the buttons/middle plastic piece of an 895max garage door remote. It isn't perfect but it worked for me. I printed it vertically with the buttons up. It doesn't matter much cause it'll use lots of support either way. The…
Small enclosure for a Duet Maestro and a Meanwell LRS-150 or similarly sized PSU. The front and back parts can be printed as one piece if your printer is larger than ~260mm on an axis but as is it isn't modeled to print that way. I wired…
ReDuplicator converted to MGN12 rails on X and Z. New 90deg fan duct should allow 255mm max z height (I got 236mm with the 45deg) Most of the original STLs reused had small defects or didn't line up so I fixed those while I was at it.…
Replacement clamp for the bungees on a foldable hand truck/dolly. Requires removal of one end of the bungees. The knob has a spot for an m3 screw for reinforcement. I'd recommend printing on its side so the rotating cylinder is vertical.…
Original plunger did not crush cans enough for me, made this 60mm longer plunger. Print outer shell at 140% to match
To wszystkie aktualnie dostępne wyniki.
