P
PrintablesMarkusMaximus
Ice Skate Stand
I didn't want the blades to be on the ground and the skates to tip over anymore. So I built a stand.
- Pobrania
- 119
- Polubienia
- 9
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesMarkusMaximus
Utility Blad Boilie Cutter
I hae printed it like this: No Support PETG 0,20mm 15% Infill
- Pobrania
- 73
- Polubienia
- 7
- Ocena
- 5
P
PrintablesMarkusMaximus
SRIRACHA Bottle Stand
I printed it like this: PLA 15% Infill 0.20mm No Support
- Pobrania
- 47
- Polubienia
- 11
- Ocena
- 5
P
PrintablesMarkusMaximus
nextorchTA30 Molle Holder
I made this adapater to add my nextorch TA30 to the Tasmanian Tiger IFAK in my car. I printed it with PETG, 15% Infill, Organic Support and 0,20mm
- Pobrania
- 37
- Polubienia
- 3
- Ocena
- 0
P
PrintablesMarkusMaximus
3DLac Lack Clip
I have made a version to glue on the surface and one version with a hole to put it on with a screw. I have printed like this: PLA 15% Infill 0.20 mm No Support
- Pobrania
- 34
- Polubienia
- 6
- Ocena
- 0
P
PrintablesMarkusMaximus
Fly trap holder
The ceiling in my flat isn’t really suitable for hammering nails or pins into. That’s why I wanted to place the fly traps on surfaces instead. If you print the ‘Stick_part2’ file several times, you can extend the stick to any length you…
- Pobrania
- 16
- Polubienia
- 10
- Ocena
- 0
P
PrintablesMarkusMaximus
Partition wall in honeycomb design
You can position the feet with double-sided adhesive tape and hold several walls together with the connectors.
- Pobrania
- 15
- Polubienia
- 5
- Ocena
- 0
P
PrintablesMarkusMaximus
Peugeot Mill Cap
You can print it with PLA, PETG or what you want. I printed it with PETG, 0,20mm, 15% Infill and No Support.
- Pobrania
- 13
- Polubienia
- 0
- Ocena
- 0
P
PrintablesMarkusMaximus
Genogram stencils templates
If you want to draw a genogram (family - diagram) by hand you can use this stencils to make all the symbols look the same. I plan to continue this and upload more forms and symbols. You can print it with PLA, 0,2mm and without support.
- Pobrania
- 10
- Polubienia
- 1
- Ocena
- 0
P
PrintablesMarkusMaximus
120mm Fan Case / Mount
I made a envoirment for my mk4s out of an IKEA Plasta cabinet. To reduce heat inside I add a 120mm Fan on the back of the cabinet. You need 4x M3 screws (min. 8mm max 22mm) to bring the parts together, no nuts needed. I used PLA, No…
- Pobrania
- 7
- Polubienia
- 1
- Ocena
- 0
P
PrintablesMarkusMaximus
Imbus (2,5mm) Handle
just press the imbus in the form and add some glue to hold all wenn in place. I used: PETG / 0,20mm / 15% infill / no support
- Pobrania
- 6
- Polubienia
- 0
- Ocena
- 0
P
PrintablesMarkusMaximus
Laundry rack foot extension (vacuum robot)
This extension raises the laundry rack by 15 mm, which is sufficient to indicate an obstacle to the robot vacuum cleaner. The clip is designed for a tube diameter of about 16 mm. I printed it with PLA, PETG should do the Job even better.…
- Pobrania
- 5
- Polubienia
- 0
- Ocena
- 0
P
PrintablesMarkusMaximus
IKEA SAMLA felt gliders ADAPTER
I use large IKEA SAMLA boxes for storage under my bed. When I pull them out or push them back, I often scratch my floor covering. I have created a way to attach felt glides or fabric to the boxes. You can either stick the blocks under the…
- Pobrania
- 3
- Polubienia
- 0
- Ocena
- 0
P
PrintablesMarkusMaximus
Door - Table edge - Bumper
If the door is likely to damage the edge of the table or the table itself when opened, you can protect it with this 3D-printed part. For a tabletop 16.40 mm thick (IKEA BEKANT)
- Pobrania
- 1
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.