P
PrintablesPencilVesterr
Flipper Zero Hard Case Magnetic
Remix of J03's Hard Case for the Flipper Zero Added Magnets for closing Required hardware: 2x M2.5 x 10mm screw 2x 6mm x 3mm Magnets
- Pobrania
- 271
- Polubienia
- 41
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesPencilVesterr
R8 Collet Holder
Simple rotating R8 collet holder labelled in both metric and imperial.
- Pobrania
- 107
- Polubienia
- 13
- Ocena
- 0
P
PrintablesPencilVesterr
Jeep JK USB Adapter
Adapter to add commonly found USB modules replacing "grocery bag hook". I believe they are all about the same size. Some fitting my be required as I noticed on my USB module it was not glued together perfectly centered.
- Pobrania
- 66
- Polubienia
- 21
- Ocena
- 0
P
PrintablesPencilVesterr
Atomrc Dolphin FC Mount
Atomrc Dolphin FC Mount modified from GizFPV clean build to accept different electronics Atomrc F405Navi :FC CRFS Nano Pro :RX BN220 :GPS Skyzone TX2500 :VTX
- Pobrania
- 53
- Polubienia
- 2
- Ocena
- 0
P
PrintablesPencilVesterr
ATOMRC DOLPHIN ESC inlet Remix
Remix of szymansk design allowing for a heat sink to be placed on the ESC and easier support material
- Pobrania
- 38
- Polubienia
- 1
- Ocena
- 0
P
PrintablesPencilVesterr
PSA Jakl Gasket
Gasket for the PSA Jakl. Fits between the upper and lower. Print out of TPU
- Pobrania
- 27
- Polubienia
- 1
- Ocena
- 0
P
PrintablesPencilVesterr
Walking Pad Cup Holder
Stand Alone Cup Holder for the Sperax Walking Pad: Designed to be level when stability bar is in forward position. About 8 degrees past vertical. Hardware Required: 4x M3 washers 4x M3 Heat inserts 4x M3 Bolts - I used cap heads, but I…
- Pobrania
- 25
- Polubienia
- 2
- Ocena
- 0
P
PrintablesPencilVesterr
Atomrc Dolphin FPV Tilt Mount
Tilt Mount / Nose Cone for the Atomrc Dolphin Only tried with analog so far but would probably fit a digital camera too. Nose cone should provide ample airflow into flight compartments Requires 1x 9gram servo and slight modification to…
- Pobrania
- 24
- Polubienia
- 3
- Ocena
- 0
P
PrintablesPencilVesterr
Razer Blade 16" Laptop Foot
Replacement foot for razer blade 16" laptops. Print in TPU and glue on.
- Pobrania
- 22
- Polubienia
- 0
- Ocena
- 0
P
PrintablesPencilVesterr
FT Goblin Tilt Camera Mount
Quick tilt mount I designed for the Flitetest goblin. Works as a replacement for the wooden FPV camera mount that comes with the kit enabling tilting the camera down. Uses one 9gram servo screwed into the backplate, superglue would work…
- Pobrania
- 16
- Polubienia
- 2
- Ocena
- 0
P
PrintablesPencilVesterr
Walking Pad Tray
Tray table for the Sperax Walking Pad: Available in LH or RH side versions. As well as cup holder version for RH side Designed to be level when stability bar is in forward position. About 8 degrees past vertical. Hardware Required: 4x M3…
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.