Liczymy pasujące modele…
This was made in 2018 for the Original Ender 3. It may work for current/newer versions but I can't confirm it. 24/05/2018: Updated to v2 which reduces filament by about 25% and print time by about 15%. This will support the Z-motor and…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ I'd recommend printing in PETG at least, although around 30% of my initial testing was done with PLA and didn't notice any issues. Updated 19/05/25: Fixed an issue…
This can be a replacement for a missing wiper cap cover on the Mazda Mx5 Mk1 or Mk2. Made using measurements from the original to match as close as possible. This is a snug fit so you might need to gently tap it in. This can be a…
This was made in 2018 for the Original Ender 3. It may work for current/newer versions but I can't confirm it. This will smooth out the passage on the 20x40 frame underneath the bed where the cables sit to prevent them from rubbing on the…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ Uploaded: November 4, 2023 Reverse engineered CAD model for the EnderXY. Printer was dissasembled and each part measured and printed to compare for maximum accuracy,…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ This upgrade will require a mainboard that has 3 independent stepper drivers available for Z (I use an Octopus board). Fixes the main issue with the EnderXY were the…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ I've made this as I've received a few messages on here asking if there was a way to fix the bed wobble without using triple-z. This is untested as I use triple-z, but…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ These are a direct replacement for the belt tensioners on the EnderXY. The stock tensioners have many issues when running higher speeds/accel such as belts slowly…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ These are untested on a stock machine as I'm using a Rapido UHF and my toolhead sits lower than stock but I've been running them for a few weeks now. The Z endstop…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ Rear cable guide to hold toolhead cables vertically at the rear of the EnderXY. May need supports depending on cooling. Required Hardware: 1x M3 x 4mm x 5mm thread…
Kusba Accelerometer mount designed for the Satsana Dual 5015 Fan Duct. Very simple print, extremely sturdy with locating pins. Supports 4010 fans and 4020 fans. Simply unscrew the two top screws for your fan and put the two locating pins…
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ Edit: This appears to be correct for the first batch only. If yours has more holes then this backplate will be incorrect. Check the remixed version for the updated…
The T12 soldering iron doesn't fit correctly in the Hakko FH-300 soldering stand as it sits at an angle and the tip of the soldering iron will touch the bracket inside the FH-300 stand. This prevents that from happening and allows the…
This was made in 2018 for the Original Ender 3. It may work for current/newer versions but I can't confirm it. This will fill the gap between the SD card slot and the outer case on the Ender-3 so that there will be no chance of slipping…
These are some extensions for the Parkside Hand Drill Set vice. The original was too narrow for what I needed so I made some extensions that allows 115mm over the original 53mm. It has 2 interface points to allow the original width to…
To wszystkie aktualnie dostępne wyniki.
