Liczymy pasujące modele…
I wanted a speaker deflector for my G90 that was low profile enough to fit in a pack and also be the same height as my Ham Gadgets Ultra Pico Keyer, this is what I came up with. No need to take the radio apart for install, but you will…
I wanted to replace the Xiegu factory power connector with powerpole. I took inspiration from one I saw on a FT817. The first one I made does not require the radio to be opened. Just put a powerpole connector on the end of the factory…
Simple cover to protect the rotary encoders and buttons on a QMX when in a pack. This version is for the original factory knobs. Print the main model by itself for a minimal cover or 2 of the round pieces and glue them to the main model…
I didn't want to drill holes in my original cover, so I created a cover I could modify as I wanted.
Case to store the CW Morse SP4/N0SA paddle for protection and can also be used to protect the paddle from accidentally sending dits/dahs by touching the adjustment screws while sending CW. Use Velcro to hold the paddle in place in the…
I wanted a cover for my CFT1 to protect the screen, buttons and knobs when I put it in a pack. I wanted something that was easy to print, required no support and looked as good from the bottom as it does from the top. Print out all the…
I couldn't find a model for the original shape & size of the Vibroplex Bug feet or what they call "bumpers", so I designed this. It should be the same size as original. I printed them out of TPU at 50% infill, you could probably get away…
I like the look of HamRadioDudes G-106 side rails over the ones that I had originally designed, but felt they needed some tweaks. These rails are harder to print than mine, I recommend using tree supports and print them in the orientation…
Simple minimal thickness cover to protect the rotary encoders and buttons on a QMX when in a pack. The four 10mm magnets can be 1.6mm-2mm thick. The knobs are slightly modified versions of the KF0ARE QMX knobs here on Printables. I added…
I wanted to mount a tiny straight key on my Quansheng UV-K5 HT for easier portable ops and this is what I came up with.
This is a basic cover for the Emtech ZM-2 tuner to protect the knobs and switches when in a pack and can also be used as a stand. Depending on the orientation of the cover either 30 or 60 degrees, use a velcro strap or rubber band to hold…
I wanted to replace the permanently attached cable on my CW Morse SP4 N0SA paddle with a 3.5mm jack. I used some 28 ga stranded wire I had, similar will work fine. I also used the same jack that, Adam K6ARK, uses on his paddles, they are…
I am a fan of N0SA CW paddles, but i don't like the hard wired cable, I prefer a jack, so here is a bottom that can be added with no modification other than unsoldering the cable and soldering the wires to a jack. It requires some wire, 2…
Protective case for N0SA's Rich Lite Portable (RLP) CW paddle. One version uses 10mm magnets for a satisfying click to lock it in place. The other version is a simpler print and a rubber band or Velcro strap can hold it in place. ***…
This is a remix of W7DLR's Morserino case. It is a smaller case & cover, I made the power switch hole larger, allowed for a 9mm thick Lipo battery internally and no LoRa antenna. If you use a 3.7v Lipo 9mm thick drone battery, it can be…
I had a key that was missing the shorting bar knob. I could find plenty of the larger key knobs, but no shorting bar knobs, so I designed this one along with the other 2 parts. This is a simple 130x72x6mm base which should fit many morse…
I am a fan of this CW paddle, but I don't like the hard wired cable, I prefer a jack, so here is a bottom that can be added with no modification other than unsoldering the cable and soldering the wires to a jack. It requires some wire,…
I wanted an enclosure for my Ham Gadgets CW Pico Keyer Plus, this is the result. It requires no tools to open or close.
To wszystkie aktualnie dostępne wyniki.
