Liczymy pasujące modele…
Simple cover to close the empty holes in my AeroGarden Harvest aeroponics system. This stops light from ruining the roots (use opaque filament) and reduces algae growth. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No…
Wydruk około 0,30 €–0,36 € nettoWstępna wycena jednego wariantu
Got uncomfortable and fed up with tracker straps and designed something more sturdy, comfortable and practical. Designed to fit HTC Vive Tracker V3.0 USB available without removing the tracker 1/4” printed screw to fasten the tracker…
Wydruk około 1,01 €–1,23 € nettoWstępna wycena jednego wariantu
Weather protection with a 3D-printed gill shield (Stevenson screen is a box) for RuuviTag temperature/humidity/pressure sensor. Basically a DIY bluetooth weather station. Keeps the water out yet enables the air and bluetooth to go…
Wydruk około 2,05 €–2,51 € nettoWstępna wycena jednego wariantu
Tested to work nicely on Varjo Aero headset. Don't use PLA as it will make the mounting fingers too fragile. Printed in vertical orientation with generous supports. Update about XR-3: This occludes the LiDAR in the center and can leave a…
Wydruk około 2,82 €–3,45 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ceiling or under-the-table mount for Valve Index headset. Designed to be easily 3D-printed based on the measurements from the headset. Recommended 3 perimeters with 2 mm brim to keep the corners from lifting up. 0.15 mm layer height…
Wydruk około 2,43 €–2,97 € nettoWstępna wycena jednego wariantu
This will make your FOV and overall experience worse, but if you need it - here it is. 3mm riser plate for my Varjo Aero VR headset. 🎮 This handy modification creates extra space between the headset and the face cushion, which is perfect…
Wydruk około 3,59 €–4,39 € nettoWstępna wycena jednego wariantu
This is a preview and a first prototype, under active development.
Wydruk około 8,71 €–10,65 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Makes the system leak potentially on the shelf underneath instead of water spreading inside the roof panel. Drill 20mm hole to roof and IP-rated junction box Cut the tube to length Install with generous amount of sealant Print from PETG…
Wydruk około 0,97 €–1,19 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Uses the original mount that came with the base station, replaces the base plate. Printing Print the flat side down to gain most ridgidity. Print from a filament that can handle some tension over time without bending. PETG or ABS…
Wydruk około 1,25 €–1,53 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Basic speaker stand for Cambride Audio's Minx Min 22 satellite speakers to act as Dolby Atmos ceiling channels. Clips into 20x20mm aluminum tube in a lowered acoustic ceiling section. Hooks neatly into the speaker's mounting point with…
Wydruk około 1,33 €–1,62 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ceiling or under-the-table mount for Valve Index headset and Varjo Aero. Designed to be easily 3D-printed based on the measurements from the headset. Recommended 3 perimeters with 2 mm brim to keep the corners from lifting up. 0.15 mm…
Wydruk około 1,85 €–2,26 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Built a lowered acustic ceiling segment in my living room, with 20mm x 20mm aluminum tubes as edges. These are designed to be clipped on the edge, and form the cable management triangle in the middle. Two versions, hook design differes…
Wydruk około 0,85 €–1,04 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Basic electrical installation box cover I needed to cover unused lightswitch hole in the wall. Top surface is designed for the filler material to grab on to. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No…
Printed face-down to girve the front nice texture from the print bed. Requires supports. Configure Vseeface “Rotation X” to 65 degrees which I found to be optimal for Vtube applications.
Cessna Skyhawk C172 Throttle Knob DIY Flight simulator use, not suitable for real plane. Missing some mechanics and aviation related certifications. Feels good in the hand Can easily be distinguished by touch from the shape alone For 5 mm…
Cessna Skyhawk C172 Mixture Knob DIY Flight simulator use, not suitable for real plane. Missing some mechanics and aviation related certifications. Feels good in the hand Can easily be distinguished by touch from the shape alone For 5 mm…
Friction locks for engine controls DIY Flight simulator use, not suitable for real plane. Missing some mechanics and aviation related certifications. Does not actually add friction, just for looks Different heights for throttle and…
Needed a clean way to semi-permanently mount a Rode lavalier mic to my Varjo Aero virtual reality headset. Pop-filter holds the mic in place and the mic is easily removed, yet sturdy.
Combine with the original model to make the full assembly.
To wszystkie aktualnie dostępne wyniki.
