Liczymy pasujące modele…
This replacement cartridge bracket will let you play Japanese titles on your US N64. Simply disassemble your N64 and replace the existing cartridge slot bracket with this universal bracket. It’s that simple. Install Guide Updated design…
The Macro F is a full shell conversion kit for the Nintendo DS Lite. It has a unique cut out to show the Game Boy Advance cartridge label and supports up to two Nintendo Switch speakers. The Macro F also uses the Boxi Pixel Macro Glass…
This is a simple tool to help remove the Nintendo 64's RAM packs. I designed this because I no longer have the original RAM removal tool that came with the expansion pack. Printing Settings: Print 100% infill on its side PETG is…
This is a replacement battery door for the Sega Saturn. The OEM Saturn battery door's tab protrudes out further than the face of the door. This would interfere with printing it flat to get the best surface, so I designed this door in two…
This is a direct replacement for the PS1's IO door. Printing Instruction: Print it flat on it's face No supports really needed but you could using them on the left tab.
These are direct replacement feet for the Nintendo 64. Printer Settings: 0.2mm layer height At least 20% infill
These are drop in replacement cartridge doors for the Nintendo 64. Printer Settings: 0.2mm layer height At least 20% infill Optionally, adjust infill direction to be along the same axis as the doors run so the top layer matches the axis
I designed these cartridge cover to stop dust from collecting in the Atari Jaguar's cartridge slot. The cover is slightly press fit to be held in place by friction without damaging the console's shell.
This is a more accurate version of my FDM printed Playstation 1 I/O door. I designed it for my Anycubic Mono X resin printer. Note: the door “hinge” hoop can get very brittle and requires some give to release the door. I suggest adding…
Back in 2019 I designed this consolized MVS for use with an MV1C arcade board complete with S-Video, Composite, Stereo Audio, and RGB out. The footprint is about the size of a Sega Dreamcast and prints great on a Prusa MK2/3 or similar…
This is a simple vertical stand for the ill-fated Steam Link. It holds the Steam Link vertically at a slight angle. All ports are accessible but disconnecting the Cat5 will require you to lift the Steam Link out of the stand. Printing…
I designed this cover to give the Atari Jaguar's controller port area a cleaner look while the controllers are in storage. It's held on by just enough friction to stay in place and not damage the shell.
A replacement AV Expansion door for the Panasonic FZ-10 3DO. This is a direct replacement for the OEM door and fits exactly like the original. Unlike the original door, this replacement has an added finger cutout allowing for much easier…
This FDM printed bracket helps mount an SD Card extension cable (not included) to the “AV expansion” bay of your FZ-1 3DO. This is an alternative to cutting a hole in your 3DO’s CD-ROM drive door to expose the ODE’s USB port. The two…
These simple brackets hold your FZ1 3DO’s CD-ROM drive door to the top shell. These are meant to be used when using Mnemo’s ODE. When you install the ODE, you remove the drive and the CD-ROM door is attached to the drive. When there’s no…
The 3DO XPort ODE is an awesome device which unfortunately shipped with electrical tape around the console side connector. This shell replaces the electrical tape and adds some piece of mind and rigidity to the cable. Designed for 0.3mm…
This is a simple drop in replacement for the original Sega Saturn cartridge door. It's designed to print easily without supports on FDM printers. There are three parts, the cart door, left arm, and right arm. The arms slide into the cart…
I designed this cover to keep dust out of the Atari Jaguar CD's cartridge slot. It's slightly press fit and held in place by friction without damaging the shell.
I designed these caps to protect Atari Jaguar controllers while they're in storage. The Atari Jaguar uses a common VGA like DB15 connector for it's controller ports. Unlike other hardware makers, Atari decided to have the male end of the…
These are direct replacements for the Whirlpool WDT710PAYB6 Utensil Rack (part# WPW10671904). Save yourself $20. Printing Settings: Print these in a stronger filament like PETG, ABS, etc. Supports needed
I designed these brackets for my own personal Game Boy Zero build but I wanted to make it modular to fit other people's needs. These brackets allow the entire front install to be taken apart and put back together without messy hot glue.…
This is an older design and concept I made back in May of 2020. I got the idea of power the Sega Nomad via the AV port with 5v from an old “The SegaHolic” YouTube video. I thought it would be cool to supply a 4400mAh and Adafruit…
Some users of the Jag2SNES were worried it hangs off the back of the AV port without any support. This brace helps with this concern.
This simple designed latch helps keep the arm on a failing McKay 16 oz can crusher upright. I got sick of our McKay can crusher arm randomly falling down and smacking the wall. This latch fixes the primary design flaw and has just enough…
This is a simple shelf for a 410x310x180mm junction box, typically used for Trinket Swap boxes. Printing Use temperature appropriate filament if you're using this shelf outside. I used PETG and it's held up very well. Print the shelf…
To wszystkie aktualnie dostępne wyniki.
