P
PrintablesAverageSauce
M6 Knob
This is a knob designed to fit an M6 bolt, you just need to snap it in after printing, enjoy!
- Pobrania
- 454
- Polubienia
- 34
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesAverageSauce
Clamp for 30mm tubes
This is a simple clamp for a 30mm tube, common measurement in fishing gear. I'ts designed to fit a square tube in the front but it could easily be modified to fit any kind of accessory. Uses an M5 bolt and nut for the fastening mechanism,…
- Pobrania
- 367
- Polubienia
- 74
- Ocena
- 5
P
PrintablesAverageSauce
VESA adapter (75->100)
I needed a VESA adapter for a monitor stand I had lying around, the problem is that my monitor had a 75mm VESA mount instead of the 100mm the stand has. I decided to design the adapter itself and the spacers separately because I found it…
- Pobrania
- 318
- Polubienia
- 17
- Ocena
- 5
P
PrintablesAverageSauce
Moza R9 riser/reclined base
This is a simple angled mount, it's made of 2 pieces just for versatility since the first plate is a flat one made to just rise the whole assembly higher. The second plate is the one that angles the mount, you just need long M5 bolts that…
- Pobrania
- 247
- Polubienia
- 13
- Ocena
- 0
P
PrintablesAverageSauce
Ender 3 max - linear rail y axis mount
This is a plate to mount the Ender 3 MAX bed carriage to linear rails on the Y axis, you'll have to print 2 of these.
- Pobrania
- 172
- Polubienia
- 19
- Ocena
- 0
P
PrintablesAverageSauce
Ender 3 Max - Y axis linear rail carriage
This is a new carriage I designed for the bed of my Ender 3 Max, the first mounts I designed resulted a bit too flimsy so I wanted to try a mount that was designed all in one piece.
- Pobrania
- 131
- Polubienia
- 19
- Ocena
- 0
P
PrintablesAverageSauce
Heroforge mini case
This is a simple case I designed for my heroforge mini, strange poses or tall hair/hats/weapons might not fit, so be sure to check dimensions. Also I glued some foam all around the inside for added protection.
- Pobrania
- 93
- Polubienia
- 20
- Ocena
- 5
P
PrintablesAverageSauce
Guitar Hero (Wii Les Paul - USB C port adapter
I converted my Wii les paul to usb with an arduino, and I wanted to take it to the next step by making it USB C compatible with a usb C breakout board. This is just a little adapter to make the port fit in the hole taht was used for the…
- Pobrania
- 88
- Polubienia
- 8
- Ocena
- 0
P
PrintablesAverageSauce
Yet another magnetic shifter
These are my own magnetic paddle shifters for sim racing, the hardware needed is M3 nut and bolt for the hinge M3 nuts for the captive slots on the inside, wich are intended for mountingthe shifter 4 10x3 magnets (you could try and go for…
- Pobrania
- 66
- Polubienia
- 13
- Ocena
- 0
P
PrintablesAverageSauce
Lower Z brace - Ender 3 Max
I like the universal mechanism of this brace, and I needed one compatible with Kevinakasam's belted Z axis, so I tried adapting the lower brace to use it with my Ender 3 Max. Also, it's kid of an ugly hackjob but it seems to be viable. (…
- Pobrania
- 40
- Polubienia
- 5
- Ocena
- 0
P
PrintablesAverageSauce
Amazon basics microphone - mic stand adapter
I designed this to mount the amazon basics microphone (yeti style) to a mic pole, and be able to point it down, while using the omnidirectional settings. All this to stream a DND session on discord :D
- Pobrania
- 36
- Polubienia
- 2
- Ocena
- 5
P
PrintablesAverageSauce
Belted Ender 3 MAX - MGN Right side dedicated mount
I designed this to reduce weight and size of the right side X axis carriage, its deigned to fit the “belted Z mod" for the Ender 3.
- Pobrania
- 28
- Polubienia
- 4
- Ocena
- 0
P
PrintablesAverageSauce
SauceForge - LGX Lite hotend for linear rails with modular/magnetic fan ducts
This is the first version of the hotend I've been modeling for a while, and the base principle I followed was to make everything easily accessible, it is designed to support the LGX Lite from Bondtech but since the plate is removable…
- Pobrania
- 25
- Polubienia
- 9
- Ocena
- 0
P
PrintablesAverageSauce
9V battery / USB conversion
Hi, I needed to power a device running on a 9V battery, with a usb power bank so I designed this. I'm not an electrical engineer so do this at your own risk :'D (So far nothing bad happened ) To make the contacts I just used aluminium…
- Pobrania
- 21
- Polubienia
- 5
- Ocena
- 0
P
PrintablesAverageSauce
RODE Videomic PRO // desktop mic conversion
This is just a simple stand I designed to hold my videomic pro, to capture some voiceovers and just for normal use as well. I must say if you have one laying around, try it, it really has a superb quality for everyday use. I used 2 M4…
- Pobrania
- 20
- Polubienia
- 2
- Ocena
- 5
P
PrintablesAverageSauce
Chair arm accessory clamp (IKEA MARKUS)
I'm just getting into making my own designs, so I just had the random thought of hanging various accessories from the arm of my chair ( for example my driving sim shift stick ) The actual STL is a new version from the one in the little…
- Pobrania
- 16
- Polubienia
- 4
- Ocena
- 0
P
PrintablesAverageSauce
Microswiss smooth idler arm
In search for the holy grail of fixes regarding what is mostly known as issue 602 (inconsistent extrusion stuff) I had the idea of trying out a smooth idler on the microswiss DD, it fits a 624zz bearing held in place by M4 bolt. Goes…
- Pobrania
- 13
- Polubienia
- 1
- Ocena
- 0
P
PrintablesAverageSauce
Amazon basics microphone - Adjustable pop filter
I use an amazon basics condenser mic on my desk (yeti clone), and I mount it on an arm so I had the original support mounting holes free to hook a filter onto it. The thing definitely works and I'm happy with it, the grill is just 2…
- Pobrania
- 10
- Polubienia
- 2
- Ocena
- 0
P
PrintablesAverageSauce
JBL Quantum TWS air - Desk mount
I needed a quick and dirty way to mount my quantum tws air earbuds case in a convenient place, so not much work went into this model but it does the job. I just secured the case with 4 little dabs of hot glue in the corners so it's easily…
- Pobrania
- 0
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.