Liczymy pasujące modele…
It didn't turn out perfectly, but from a distance, it looks like Frieren. (;'∀') Print with 100% infill and a layer height of 0.08mm. Set the base layer to 0.16mm. Filament swap sequence:Initial filament: Black Switch to next filament at…
Print at 100% fill rate with a 0.08mm layer height. The base layer is 0.16mm. Swap Procedure: Initial filament: Black Switch to next filament: Gray at layer #11 (0.96mm) Switch to next filament: White at layer #14 (1.2mm) (use until final…
The Input Shaper needs to be calibrated from time to time. This is necessary after changing the installation location, adjusting the belt tension, or changing the area around the Nextruder.
Print at 100% fill, 0.08mm layer height. Base layer 0.16mm. Swap Steps: Initial filament: Black Layer #10 (0.88mm): Switch to next filament: Lipstick Red Layer #12 (1.04mm): Switch to next filament: Gray Layer #15 (1.28mm): Switch to next…
This is a protective and display case for a holder that holds 25 x 5 (125) MakerChips. This holder is for poker coins, look elsewhere. jonk | ホーム - MakerWorld I print my holders 5% larger than the originals.
This is a display case for dried flowers. It prevents them from falling over and makes them look nicer.
There are two sizes of base, each with two grooves of different widths. I printed it using PLA and haven't had any problems. It's light, so I recommend fixing it in place with double-sided tape or something similar.
Print at 100% fill rate with a 0.08mm layer height. The base layer is 0.16mm. Swap Instructions: Initial filament: Black Layer #10 (0.88mm): Switch to next filament: Orange Layer #12 (1.04mm): Switch to next filament: White (used until…
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Black Switch to the next filament at layer #10 (0.88mm): White Switch to the next filament at layer #12 (1.04mm): Sky…
Print at 100% fill, 0.08mm layer height. Base layer 0.16mm. Swap Procedure: Initial filament: Black Layer #7 (0.64mm): Switch to next filament: Terracotta Layer #11 (0.96mm): Switch to next filament: White (used until final layer)
Print at 100% fill rate with a 0.08mm layer height. The base layer is 0.16mm. Swap Procedure: Initial filament: Black Switch to next filament: Galaxy Silver at layer #8 (0.72mm) Switch to next filament: White at layer #13 (1.12mm) (use…
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Black Switch to the next filament at layer #8 (0.72mm): Green Switch to the next filament at layer #10 (0.88mm):…
Print with 100% infill and a layer height of 0.08mm. The base layer is 0.16mm. Swap Procedure: Initial filament: Black Layer #12 (1.04mm): Switch to next filament: Blue Layer #15 (1.28mm): Switch to next filament: Sky Blue Layer #17…
Print at 100% fill rate with a 0.08mm layer height. The base layer will be 0.16mm. Swap Procedure: Initial filament: Black Switch to next filament: Gray at layer #10 (0.88mm) Switch to next filament: White at layer #15 (1.28mm) (use until…
Print at 100% fill rate with a 0.08mm layer height. The base layer is 0.16mm. Swap Procedure: Initial filament: Black Layer #8 (0.72mm): Switch to next filament: Gray Layer #15 (1.28mm): Switch to next filament: White (used until final…
It can hold about 30 MakerChips. I printed it using PETG with a 0.6mm nozzle.
It was printed in PLA. This is a cup made for brushing teeth. It's a rare shape, isn't it?
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Black Switch to the next filament at layer #8 (0.72mm): Green Switch to the next filament at layer #10 (0.88mm): Cyan…
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Black Switch to the next filament at layer #11 (0.96mm): Red Switch to the next filament at layer #14 (1.2mm): Gray…
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Green Switch to the next filament at layer #6 (0.56mm): Chelsea Red Switch to the next filament at layer #9 (0.8mm):…
It didn't turn out perfectly, but from a distance, it looks like Frieren. (;'∀') Print with 100% infill and a layer height of 0.08 mm. Set the base layer to 0.16 mm. This print uses three types of filament. Filament swap procedure:Initial…
Print with 100% infill and a layer height of 0.08mm. The base layer should be 0.16mm. Swap procedure: Initial filament: Black Switch to the next filament at layer #7 (0.64mm): Green Switch to the next filament at layer #9 (0.8mm): Yellow…
It can also be used with other sprays, provided the diameter is under 40mm. By the way, this sanitizing spray is perfect for cleaning the build plate; it contains a small amount of alcohol, so it leaves the surface very clean.
It didn't turn out perfectly, but from a distance, it looks like ubel. (;'∀') Print with 100% infill and a layer height of 0.08 mm. The base layer should be 0.16 mm. Filament swap procedure:Initial filament: Black Switch to the next…
It didn't turn out perfectly, but from a distance, it looks like Frieren. (;'∀') Print with 100% infill and a layer height of 0.08mm. Set the base layer to 0.16mm. Filament swap sequence:Initial filament: Black Switch to next filament at…
Print with 100% infill and a layer height of 0.08mm. Set the base layer to 0.16mm. Filament swap sequence:Initial filament: Black Switch to next filament at layer #8 (0.72mm): Gray Switch to next filament at layer #10 (0.88mm): Terracotta…
Print with 100% infill and a layer height of 0.08 mm. Set the base layer to 0.16 mm. Filament swap procedure: Initial filament: Black Switch to the next filament at layer #8 (0.72 mm): Gray Switch to the next filament at layer #12 (1.04…
To wszystkie aktualnie dostępne wyniki.
