Liczymy pasujące modele…
Add a [labeled] handle to your box allowing easy identification from the front! This handle should fit the default V2 Prusa Tools Box (InnerBoxWidth=180, ScrewLength=30) by @3DesignsCH . Install using 35mm screws (rather than the 30mm…
Wydruk około 7,64 €–9,34 € nettoWstępna wycena jednego wariantu
Introduction All other modular Skadis models I have found either omit holes, or split holes down the center at the seams. I didn't like that look, so I created my own from scratch. Before I start, there's a lot of documentation here, not…
Remixed the rear dust protectors from @dancan13f full set (awesome, love them) so they don't cover the entire back vertical surface, and can fit an 8mm magnet. Replaced the vertical bars with a low ramp so anything that falls should…
Attach the new, compact, Buddy3D Core One camera to your Prusa XL using the official Prusa XL Camera Mount: https://www.printables.com/model/1105925-xl-camera-mount-buddy3d Should work for the XL_enclosure mount also. All pieces should be…
Trophy will need supports, all other parts can be printed flat without supports. Pictured with home-made custom decals inspired by official superbowl 59 logo. Easy assembly with dowels allows printing the parts in different colors for…
From the original author: A stylish key cover that turns any key into an electric guitar. Remixed for standard Kwikset K1 Keys
I use a brush and side cutter most often, so I keep these tools handy to remember to brush off the nozzle when loading new filaments. Set up for 8mm magnets. Designed for .2mm with no supports. Larger Hole Version: Increased size of brush…
Thick (but flexible) ruler with holes to fit a standard binder. Markings in metric and imperial units, and labeled edge-to-edge so you can butt it up against something to take an accurate measurement. The small version (25cm) ruler will…
I designed/printed this for a .4 nozzle and .2 layer height. Multi-color versions can be printed with a single extruder by printing the panels in different colors. There's no need for supports if printed with flat sides towards bed. For…
Thin and flexible, these rulers use less than 5g of filament! The small version (25cm) ruler will fit on a 21x21 cm bed. You will need a larger bed for the 30cm (12in) version. Print instructions The color change is done by layer so no…
The calibration pin is infrequently used, but essential. Keep it attached to your xl so it never gets lost. Check out my other Prusa XL Accessories: https://www.printables.com/@Jupera/collections/2212644
Easy two color print with MMU or one filament swap without. Enjoy.
This Pacman Ghosts' eyes follow you as you move! Easy to print, no supports necessary. I've included a pre-painted .3mf file for MMU printing and the basic .stl Designed for MMU, but easy to paint if you don't have one. Without an MMU it…
I use these specific tool most often, so I keep them handy so I remember to brush off the nozzle when loading new filaments. Version 2: Increased size of brush holder to accommodate large brushes (like the Prusa brush) Check out my other…
Fits microwave model NN-SN661S and possibly others. Panasonic part # F82569Y00AP Printed just fine without supports on my printer, but your mileage may vary (see orientation in photo). (Probably would have “looked” nicer in a different…
No Supports Necessary. Use a .5 inch X .062 magnetic strip to attach blades. Easily attaches to Skadis board with the amazing Skadis T-Clip System by @LineArcLine Check out my fully modular:
Bring the magic of fast travel into the real world with this detailed 3D-printed Minecraft Waystone! Designed to perfectly fit an electric tea light , it becomes a glowing beacon—a perfect desk ornament or collector's piece for any…
Mount your mini tape measure on your skadis board no supports Check out my fully modular Skadis system:
To wszystkie aktualnie dostępne wyniki.
