Liczymy pasujące modele…
This model is inspired by Jake_of_all_Trades Pulley Extractor (https://www.thingiverse.com/thing:3593964) but with changes: fillets added (for removing failure point when using excessive force) chamfer added (removed sharp edges for…
Two part assembly: base and front plate, which slides in base for assembly and is easily removable. Optional M3/M4 screws for fixing to wall.
Pyramid Lamp - only one E14 socket with cord and LED bulb needed. I have found one smaller bulb performs better than one standard sized bigger, that is why E14 is recommended. Base prints without support. Panels printed separately, no…
Size is diameter of 139mm and height of 359mm. What else can you say about oversized wine glass - if you wondering why, then you probably do not need it ;) … … or maybe?
Bear corner brace / bracket for M4 screws. Typically used in bear mod frames, but it could be for anything - Enders, CR10 any frame with 2040 extrusion profiles.
One thing to notice is that when mounting to 4mm holes there is limited access to one side (where curvature of duct direct airflow), therefore it is only possible to add M4 nuts from the sides.
Housing for audio bluetooth module VHM-314 (comes with red or black pcb). Two part print, supposed to be snug fit, but it depends on the printer. Should print fine without supports. Assembly with 2x M2x4mm screws (i simply took any length…
This model holds 4 spools which have maximum height of 71mm, so for example Sunlu, Jayo, Kingroon. Smaller 0.5kg should holds 8, but only 4 would spin independently. Another thing that distinct this design from others is that idlers have…
Simple model for housing W3230 thermostat module.
Screw M4x20+ with cone head 3pcs per leg. Anticipate quite poor access to screws; maybe do extension of screwdriver.
3 part design assembled with screws and holding to TV by magnets. Parts needed: - 3x M3x30 - 3x M3 hex nut - 2x 10x13x5mm magnet Two magnets will suffice, but if not add another two with the same dimensions on top (there is enough space…
Two versions - for D shaped shaft and circular with 6mm diameter.
It utilizes total of 4 M3 screws and two nuts (not nylock).
Heavy Duty PC Stand for adding space beneath floor and case. This design is quite easy to print and assembly you need 10mm rods and cut them for exact length of your pc case and either glue, pressfit or heat and insert those. 218mm width…
TPU or TPE is recommended for the best grip and tactile effect. Previous one simply unglued itself overtime. Therefore this design require no glue or screws. It is symmetrical part so just duplicate and print two parts.
Technically probably not hexahedron as it has more than six faces ¯\_(ツ)_/¯ Looks great while printing and on the desk as well. Gif from slicing: https://imgur.com/jWYKVmk
Affix from side with 4x conical screws of maximum diameter of 2mm.
Dimensions of AC outlet and power switch You need: 4x M3x10+ screw (two for side assembly and two for AC outlet) 4x M3 nut 2x M4x10+ screw (screws into backplate of power supply)
This is simple design providing better grip of this fiddly handtool. Should be snug fit. Precision screwdriver kit have different sizes of metal handles for each of philips size. This design is for 4mm (+0.2mm tolerance) screwdriver.…
The design is based on Prusa Bear Y axis bearing mounts. Its use case does not limit to Prusa Bear machine and even Y axis.
DIY Project that utilizes out-of-the-shelf components and 3d prints. Fusion360 model: https://a360.co/3Ne5RhL Main Features: ~100x100x110 [mm] build volume Direct MK3s extruder remixed for MK8/HobbGoblin drive gear and filament sensor…
Print it, insert it, use it. It is recommended to use modifiers or select 0 top and bottom walls, so that it has meshed bottom, aesthetics reasons aside water or dust will not accumulate on the bottom of the cup.
It consist of two pieces: lower element 2x M3nuts (nylock recommended) upper element secures via 1x M3x16 screw and nut to bed and 2x M3x20 screws to lower piece It is intended for cable loom OD 13mm
I have found that it is quite important to giving place for your most used items, when organizing your workspace - this is minimalist organizer for your typical items. I've got one at my work desk and store there earbuds, keys and…
Total model height 131mm. Suitable for any application, where adding extra grip is beneficent and M8 mounting is possible.
Original one was from nylon, but failed after two years of use. Printed in PETG, withstands cleaning in dishwasher. One year at this point and counting… Reverse engineered for your convenience ;)
This model is for ~22mm handlebar for bike. The same as those for Cortina U4 bike, but changed the handlebar to pretty standard one so it should fit more models. Best to print it with TPU/TPE or other elastomer, but PETG should be okay,…
This design does not worry about being thin. Stay cautious and slice it with your favorite profile settings or exercise no compromise approach with 100% infill or 75 solid bottom walls at 0.2mm layer height. It is functional statement…
It uses the same vitamins as in Prusa Bear mod, but use case is not limited to this upgrade.
Base is for SKR v1.1 , v1.3 , v.14 (and other SKR variants that have the same hole placement) , MKS Gen L. “ skr-electronics-box-step-down-holder ” is step down holder for 3x LM2596 and 1x LM7812 module. “skr-box-mk2s-frame-backplate” is…
This design comes with multiple versions. Distinction is that they are for storing 2 or 3 objects per stand with 22mm and 26mm width. As it is intended to be general purpose, this particular design was made having kitchen cutting board in…
To wszystkie aktualnie dostępne wyniki.
