P
PrintablesPaul
Skadis Cable Organizer
Print upright with supports for hook pegs. 20% infill used.
- Pobrania
- 849
- Polubienia
- 162
- Ocena
- 4,73
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesPaul
Skadis Multimeter Mount
Designed around the low cost Kaiweets KM100 model multimeter. The cutouts allow storage and use while mounted. Print using supports for the pegs on the back of the holder.
- Pobrania
- 722
- Polubienia
- 148
- Ocena
- 5
P
PrintablesPaul
Skadis Wire Stripper Mount
Print upright using supports for the pegs. Use a straight infill type (cubic or grid), using gyroid has the potential to knock over the support mid print. Set the support to tower and use “initial layer support line distance” of 0.5mm.…
- Pobrania
- 221
- Polubienia
- 40
- Ocena
- 5
P
PrintablesPaul
Calculator Holder - Skadis Holder
Sometimes you need easy access to your trusty graphing calculator. Rather than digging it out of your desk drawer or having it clutter your workstation, this will tuck it off to the side on your skadis board. It is modeled for a TI-84 but…
- Pobrania
- 94
- Polubienia
- 11
- Ocena
- 0
P
PrintablesPaul
Machinist Ruler Holder - Skadis
This print has drop in pockets for magnets measuring 17mm by 4mm. Print using supports for the hooks. The dividers are set for rulers with a width up to 27mm and 19mm.
- Pobrania
- 59
- Polubienia
- 9
- Ocena
- 0
P
PrintablesPaul
Cable/Test Lead Hanger/Holder (Clamp-On) 90deg remix
Rotated clamp 90 degree. Will require upright printing configuration and supports for top of clamp.
- Pobrania
- 50
- Polubienia
- 4
- Ocena
- 0
P
PrintablesPaul
SEGA GENESIS TRIPLE BYPASS (3BP) MOUNT
Mounting bracket and backing for the DIN connector used when installing a 3BP on a Sega Genesis Model 1. This comes in two sizes. The larger design includes a top cover for the 3BP board to eliminate the risk of contact with the RF…
- Pobrania
- 36
- Polubienia
- 3
- Ocena
- 0
P
PrintablesPaul
Flux Stand
Simple holder for amtech type flux or any flux in a syringe applicator. Keeps the flux from making a mess and allows you to store the applicator in a vertical or horizontal position. Simple to adjust the z scale if you would like the case…
- Pobrania
- 25
- Polubienia
- 3
- Ocena
- 0
P
PrintablesPaul
1U Server Cable Manager - 90 Degree with rail
Remix of a server cable manager to run on the outside of the rail. This was useful for my 3d printed mini-rack. The remix is a simple hack of the original mesh but functions well. Print using a brim if bed adhesion is an issue. Use…
- Pobrania
- 23
- Polubienia
- 6
- Ocena
- 0
P
PrintablesPaul
Amscope Lens and Camera Mount Cover
Simple lens covers designed for the eye pieces (with rubber eye cups) and the camera mount. Printed in TPU, but should work fine with any filament.
- Pobrania
- 23
- Polubienia
- 0
- Ocena
- 0
P
PrintablesPaul
FLASHCAT XPORT CASE
A simple case designed around the Embedded Computers Flashcat XPORT. The tolerance is tight to correctly secure the PCB. Depending of batch, your PCB might have slight variation in dimension. You should be able to adjust the x and y…
- Pobrania
- 23
- Polubienia
- 2
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.