Liczymy pasujące modele…
This strange rolling riddle will make you think twice about how things roll! In a straight line? No! It rolls in an irregular pattern like pictured below. It gives you the illusion of rolling normally, then it fakes you out! It works best…
This model is an Abstract , artistic pencil holder about 4 inches tall. It should take less than two hours to print. I recommend a lower density for printing as in some spots the walls are very thick. I printed in PLA silk that's why it…
This model is based on the F-35 Lightning II. It prints in two pieces but on the same plate, the jet itself is about 135mm long and with the base its total height is about 75mm.
This model is a plastic print-in-place bearing. It spins very well just off the print bed! Though you do have to peel a small support ring out before spinning, if you don't it wont spin smoothly.
Here I made a Dummy 13, but its only 45% of the original size! The WORLDS SMALLEST one! 0.2mm nozzle required! When assembling, be very careful! It is very fragile since it is sooo small! Its size may also restrain a little of its motion.…
This is simply a mode of a Bugatti Chiron. Its about 120mm long. Easy print, I recommend printing it upright, like the taillights are on the bed.
This model was made so that you are able to reuse your filament spools without throwing them away. It only uses about 200 grams of filament, so it makes a good last meter print. It fits in every spool Ive tried it on. The pegs that are…
This model is an coral shaped pencil holder about 3.5 inches tall. It should take about 5 hours to print. I recommend a lower density for printing (or use my 3mf) as in some spots the walls are very thick. I printed in PLA silk that's why…
Here's a pixel heart that doubles as a container and a light box! Put a tealight or something brighter inside and it turns into a lightbox! *A tealight may not be bright enough, you may want something brighter.
This model is a blow-dart gun that shoots a small dart pretty far. Plus when you are tilting it back to get the dart fully in, it doesn't go into your mouth, because there is a guard. Warning: the dart is pointed, don't make a bad…
This model was made so that you are able to reuse your filament spools without throwing them away. It only uses about 200 grams of filament, so it makes a good last meter print. It fits in every spool Ive tried it on. The pegs that are…
This finely crafted 3D-printed mini sword is designed specifically to attach to your Dummy 13 figure, adding a touch of adventure and flair. The sleek, compact design fits perfectly into the figure’s hand, offering an enhanced display or…
This puzzle is a little more challenging than my last, and its bigger too. It looks like just a cylinder until you give it to a friend and say open it, then the fun starts. You should see them pleasantly puzzling for 15-35 minutes…
This model is a medium hardness puzzle jar. It looks like just a cylinder until you give it to a friend and say open it, then the fun starts. You should see them pleasantly puzzling for 10-30 minutes, it depends on the person. Its…
Introducing our Under Shelf Mounted Benchy Display, specifically designed for showcasing your 3D-printed Benchy tugboat models! This sleek, 3D-printed display securely holds your Benchy while maximizing shelf space. Its minimalist design…
This model is a four slot measuring tape holder. It holds fairly large measuring tapes, its very strong, and it tilts upward with a ledge so that the tapes don't fall out. That I know of it fits Stanley, DeWalt, and some random off-brand…
Here's another strange rolling riddle that will make you think twice about how things roll! Does it roll in a straight line? No! It rolls in a pattern like a wave. It works best with a low layer height.
Here's a great organizer for your desk. Plus, its a benchy! It’s not just a fun print, it’s a full-on desk setup. There’s a spot for Post-it notes, a tray for small stuff, space for pens and pencils, and even a special holder for that one…
Optimize your workspace with our Filament Spool Reuse Drawers, designed to convert empty filament spools into efficient storage solutions. These modular drawers are easy to stack and customize, providing a practical way to organize your…
Flip for a showdown between Agent Perry the Platypus —secret agent extraordinaire—and Dr. Doofenshmirtz , whose evil plans are as ridiculous as they are doomed. Who will win? Probably Perry, but chaos is guaranteed either way!
This model is for all the Rubik's cube enthusiasts that are out there! If you have tons of Rubik's cubes just sitting around here's the thing for you, its a Rubik's cube holder plus it allows you to make it look good with some simple…
This model is a painting staining stand designed so that you don't have to miss any spots while spraying, and so that you don't set a wet side on your surface and ruin your paint job. Its about 6.25 inches wide and 8 inches long (between…
These are some nice 100mm wide, fully colored, Minecraft pixel heart coasters! 4x coaster holder is also included.
To wszystkie aktualnie dostępne wyniki.
