Liczymy pasujące modele…
A remix of the cable clip for use with 4040 extrusion found here: https://www.thingiverse.com/thing:5266874. This clip has a larger square opening to allow for more wires or cables. Once printed, fit the small section into the extrusion…
This adapter will allow you to use the magnet-ball/HOTAS setups with a Quest 3 controller. These setups are seen online to purchase or to print for other controllers. This one is based on the Valve Index HOTAS setup found here:…
A remix of the cable clip (https://www.thingiverse.com/thing:5266874) for use with 4040 extrusion. This clip is twisted 90 degrees to allow routing in a different direction and has a larger rounded top to allow for more wires and the use…
This is a remix of darknao's 15 degree Logitech MX Ergo Mouse Base (https://www.thingiverse.com/thing:2640807) for 40 Series Aluminum Extrusion. It can be mounted with 2 M5 bolts. It's recommended to use Industrial Strength Velcro Tape to…
This is a remix of the Belt Guide for Belt Tensioner (Sparco) by darumble (https://www.thingiverse.com/thing:4944378). This will allow the belt guide rollers to be mounted to 40mm aluminum extrusion for belt tensioners used in sim racing…
This is a remix of the Thrustmaster MFD 40x80 Profile Mount (Monstertech inspired) made by Pydrex found here: https://www.thingiverse.com/thing:6175490. Changes include 1) adding raised lines to assist in finding buttons when in VR, 2),…
This is a remix of the Virpil Controls VPC base adapter for 8020 profiles by sorcererlc (https://www.thingiverse.com/thing:4863358). This will work with the Vipril WarBRD base and has been revised to close the gap in the middle of the…
This is a simple remix of the Valve Index Controller Wall Mount that can be mounted to a 40 series aluminum extrusion with a single M8 bolt. Additional Items Required: M8 bolt M8 T-nut
This is a simple Fanatec Emergency Stop Button Bracket for 40 Series Aluminum Extrusion. I used the basic distances from the previous model and just slimmed everything down and removed the angle. I also removed excess filament to reduce…
These are a remix of the original Simtrecs Clutch and Accelerator Covers created by Alain Vdk from the Simtrecs Owners Facebook Group that required a threaded hole on the respective pedals. This remix will instead snap on easily on both…
This is a remix of the flat GoPro mount created by mark133 (https://www.thingiverse.com/thing:40282). This version allows the Sim Racing Studio Wind Kit exit tubes to be mounted to the newer DOF Reality wider Wheel Deck support struts…
This is a remix of the cable clamp created by Pyronious (https://www.thingiverse.com/thing:3688504) for actuator motion simulator platforms. The remix rounds the mounting tab so the clamp is easier to install. The original model has the…
Update: A reinforced version along with a non-reinforced two hole variant is now available. This is a mounting bracket for the Thanos emergency stop. The four hole non-reinforced version allows it to be mounted to a 40x80 piece of…
This is a simple bracket to hold the V2 Jinx Sequential Shifter controller box to 4040 aluminum extrusion. Place the brackets between the raised screw heads. This will prevent the control box from sliding out from the brackets. Holes are…
This is a bracket to hold the 24v Power Supply for the TensionR Active Belt System to 4080 aluminum extrusion. Refer to the image for the supported power supply. Holes are sized for M6 bolts. Additionally required: 2x M6 bolts 2x M6 nuts…
To wszystkie aktualnie dostępne wyniki.
