P
PrintablesNicole
M8P Low-Profile DIN Rail Mount (Full/Combined)
You'll need: 4x M3x4x5 heat set inserts (if printing the Insert version) 4x M3 spacers 4x M3x6mm or M3x8mm screws
- Pobrania
- 78
- Polubienia
- 13
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesNicole
Pump It Up - Sensor Channel (early FX)
Reverse engineered sensor channels for arrow frames. These were used in early FX model pads, later reverted back to the original design. They expose more of the sensor, likely resulting in better sensitivity (but possibly worse sensor…
- Pobrania
- 23
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Skadis Machinist Block Mount
A holder for two 1-2-3 or 25-50-75 machinist blocks, side by side. Requires 2 of CSD_Salzburg's universal hook .
- Pobrania
- 23
- Polubienia
- 9
- Ocena
- 0
P
PrintablesNicole
Pump It Up - Pool Hose Pad Harness Box
My pad harness, including the boxes, came pretty banged up. I ended up replacing the pad harness with a 1.5" by 4' pool hose, but wanted to make the boxes a little nicer too. With the current hole dimensions, the hose is even a perfect…
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Pump It Up FX - Bill Acceptor Plate
Since I was putting a capture card into my cab, I wanted a place to put some kind of plate mount USB port on the front for easy access. I ended up making a replacement plate for the bill acceptor with the opening for a generic AliExpress…
- Pobrania
- 14
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Pump It Up - MK6 PIUIO Mount
Since the PIUIO is only designed to go in an AGP slot, when I upgraded my MK6 to modern hardware I had to figure out a new solution to mount it. My friend suggested I mount it using the vent holes in the case, and that's what I ended up…
- Pobrania
- 11
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Pump It Up - Foot PCB Mount
I don't like the idea of a wooden slab sitting in my pads. See pictures for assembly. Hardware 4x M3x4x5 Heat Set Insert 4x M3x6mm Washer-Head Screw 4x M4x12mm Self-Tapping Washer-Head Screw
- Pobrania
- 10
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Pump It Up FX - Hard Drive Bay Mount
One of my friends told me they mounted their SSD in front of the operator panel. I thought it was a good idea, so I decided to take it a step further by mounting a 5.25" Hot-Swap Hard Drive Bay I had laying around from an old NAS project.…
- Pobrania
- 7
- Polubienia
- 1
- Ocena
- 0
P
PrintablesNicole
Pump It Up FX - Card Reader Mount
My FX came with card readers, but they didn't include the original box. I modeled some mounts to make them float below the visualizers because I thought it looked cool. You'll need to drill holes to properly route the cables; I've…
- Pobrania
- 6
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.