Liczymy pasujące modele…
Trading card stand. Use it for sports cards, Marvel, Magic the Gathering MTG, Pokemon, etc. Works well for cards displayed horizontal or vertical. Can be used for greeting cards or photos as well. No supports.
Remix of a hot wheels launcher that allows the launcher base to connect to standard hot wheels track. Requires two printed parts and a rubber band. Requires supports. I printed at 0.2 mm height and print came out nice.
Desk organizer, 7 versions. Version shown in photos has date wheel holder in back with cutouts in bottom to save a little material. One version omits cutouts and one version omits date wheel holder. Added versions to accommodate a 6x9…
Supports required. Will fit on an Ender 3 Pro standard print bed if angled. Not sure about other printer beds. Works with standard Hot Wheels track pieces. See photos.
For optimal strength print with bottom of hanger against print bed. No supports required.
No supports needed if round portion is facing up.
I needed a wall mount / shelf for my new Ring Indoor Cam. Designed so the USB cable can pass through a slot in the back of the holder. Simple install w/ 2 screws or command strip. No supports required. Printed in PLA+ with 20% infill.…
No supports required. Design asymmetrical due to location of left hand Honda Fit cupholder.
Expandable pliers rack. Remix of la_mecanique's model. Shortened by about 10 mm, and added slight taper to end of connecting pegs. No supports needed,
Printed in PLA+, 30% infill, no supports. STL file is slightly revised from photos to allow for better unsupported print. Designed to snuggly hold either beer/soda cans/bottles, or larger coffee mugs.
Bit holder for ¼" bits. Two versions, one is sized to press fit in a bit, the other is scaled up 10% for a looser fit, and you can glue in a 5 mm or 6 mm magnet to hold the bit in place.
Printed in flexible PLA, at 99% scale for slightly tighter fit. Same print works for both upper and lower jaws.
Holes are sized based around printing model at 75% X and Y, 100% Z.
Foot for end of horizontal leg tube of Lifetime folding tables. Leg tube is approximately 20mm x 35mm. I printed in flexible PLA, and fits on well when secured with stock screw through table leg. There's a hole in printed piece that…
I wanted a slightly smaller version of parrothead270's bottle cap catcher. This version fits nicely on the face of a 4x4 (or 2x4). Dimensions of this one are 75 mm wide, 40 mm deep and 67 mm tall. Print Settings Printer Brand: Creality…
Cylinder is 16mm in diameter which was designed to fit nicely in the pipe insulation I purchased. I added a small hole in the cylinder so that a wire or string can be threaded through the sides of the “arm” and the claw/hand to hold it in…
No supports needed.
The idea is this is a simple passthrough (flanged on one side), that can be glued or taped in place on millwork doors, etc. The version I printed is 125% in X/Y coordinates, which makes it about 6" height and width.
I had an extra aluminum extrusion and window blind material but needed mounting hardware. I created parts to hold the window blind in place, allow it to be rolled up and kept in place at desired height. Support needed on gear looking…
I made this model at these specific dimensions as a means to elevate shampoo/conditioner bottles within a pre-made shampoo bottle holder. The model has an open grid design so that water will flow through it, and the rim is slightly…
Easy print chopstick rest. Two versions, one with sharp corners/edges, one with filleted corners/edges. Added hollow version to more closely emulate the folded paper inspiration. Supports should not be needed.
Print on side with no supports needed. I did 50% infill in PLA+.
Two replacement pieces to a Lovevery toddler stacking shape toy.
To wszystkie aktualnie dostępne wyniki.
