P
PrintablesCeasar
Climbing Hangboard V2 3D Printable
Made upgrade version from V1 to add a jug type hold on the top of the old
- Pobrania
- 297
- Polubienia
- 36
- Ocena
- 4
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesCeasar
IKEA Faktum leg clip replacement for skirting/kickboard
Replacement parts for old IKEA kitchen that is not produced anymore.
- Pobrania
- 234
- Polubienia
- 9
- Ocena
- 0
P
PrintablesCeasar
Pipe notching template guide
Made quite a few pre made notch templates for my bicycle project, for multiples angels. Will add more sizes and also try to figure out a model scale to pipe diameter ratio. Name convention is: M - Master (pipe you are going to notch) S -…
- Pobrania
- 226
- Polubienia
- 35
- Ocena
- 0
P
PrintablesCeasar
jaw trainer exerciser
Made a jaw toner to train jaw muscles. Work good, you can alter how much resistance/force you want by changing the width of the toner. Might be a bit big for small mouths but if you scale it down the force to bite will increase so please…
- Pobrania
- 204
- Polubienia
- 11
- Ocena
- 0
P
PrintablesCeasar
Carcassonne Meeples & Pope
Just a simpel model of the Meeples and Pope from Carcassone, the Meeple have been on a diet and is a tiny bit slimmer but is correct in rest measurements. Will add some variations for the fun of it with some hats and body styles. Print i…
- Pobrania
- 187
- Polubienia
- 18
- Ocena
- 5
P
PrintablesCeasar
Car Cup holder universal (VW Multivan T4 replacement)
Made a tray and ring to suit the model made by LukasJanik since my was lost when I bought my van. I also made a simplify version of his model as well to suit the tray better and make easier to print. Added a rubber inlay for the ring to…
- Pobrania
- 139
- Polubienia
- 12
- Ocena
- 5
P
PrintablesCeasar
IKEA BILLY Bookcase 80 cm
Just a real size model of IKEA BILLY that i created to make wall connection so needed it to model after. Model from measurement of IKEA+real life measurement, I did not add the odd variant of shelf holes but the basic ones should be…
- Pobrania
- 109
- Polubienia
- 8
- Ocena
- 0
P
PrintablesCeasar
Climbing Hangboard 3D Printable
A hangboard to train you fingers/grip for climbing have 3 different levels of 30-20-10mm. Made them to screw into the well above a doorframe. Bolt hole are for m6 and also added a standard washer (m6 with 12mm outer diameter) to…
- Pobrania
- 96
- Polubienia
- 26
- Ocena
- 0
P
PrintablesCeasar
Climbing Hangboard V3 3D Printable grip texture
Made yet another upgrade version from V2, here is V3 Made Slic3r pre-set with fussy skin to add grip texture. removed a bit of material so it would print more efficent. Tested lower infill and parameters. I weight about 105 kg and Slic3r…
- Pobrania
- 69
- Polubienia
- 7
- Ocena
- 5
P
PrintablesCeasar
Pixel 6A Quadlock case
Used The stick adapter and morphed it into a pixel case. Can be printed in one go with TPU and works fine however supports are a bit tricky to get dailed in. I now run the case in a two material configuation, TPU case and sliced the part…
- Pobrania
- 67
- Polubienia
- 6
- Ocena
- 0
P
PrintablesCeasar
VW T4 speaker upgrade 6.5 inch and tweeters transport/caravelle/multivan
Updated my speakers on my van and needed to make som adopters. one 6.5 and tweeter upgrade booth are made to be basic to print so not super much details, but worked fine. The 6.5 door speaker neede just a bit more distance from the…
- Pobrania
- 63
- Polubienia
- 12
- Ocena
- 0
P
PrintablesCeasar
IKEA BILLY Bookcase 40 cm
Just a real size model of IKEA BILLY that i created to make wall connection so needed it to model after. Model from measurement of IKEA+real life measurement, I did not add the odd variant of shelf holes but the basic ones should be…
- Pobrania
- 55
- Polubienia
- 7
- Ocena
- 0
P
PrintablesCeasar
Nauticat 33 steering wheel spacer
A replacement for nauticats deckhouse steering wheel bushing/spacer since this replacementpart dont seem to be able to get bought. Printed it with PETG at 100% infill, since its mounted with compression i do not recommend to print with…
- Pobrania
- 13
- Polubienia
- 3
- Ocena
- 0
P
PrintablesCeasar
VFR800 RC46 speedo socket
My adapter for speedo was worn out so made a simple 3d model to replace it. Now driven 2000km on it and seem to hold up good in PETG.
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.