Liczymy pasujące modele…
This design allows you to hold an A1 Lidar from RPLidar to the Turtlebot3 waffle plate. The waffle plate is a module robot base platform used in the open source Turtlebot3. The attached 3mf file includes my selection of variable layer…
Wydruk około 1,65 €–2,01 € nettoWstępna wycena jednego wariantu
This battery cap will hold itself in place with small tabs “hugging” the Battery posts. The specific design is for the N70T Deep cycle design. This deep cycle battery has secondary smaller 8mm threaded posts for attaching inverters, solar…
Wydruk około 2,14 €–2,62 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A Project Box to fit the Velleman Voice Changing Electronics Kit
Wydruk około 4,26 €–5,20 € nettoWstępna wycena jednego wariantu
This is a rack and pinion style linear actuator. Due to the inclusion of a worm gear drive, the rack will maintain its position without the requirement to "hold" the gears static with a motor. This requirement was necessary in the…
A very basic 4% grade to place under your HO track to create an incline. This design is about as basic as it gets Print instructions Tested between .15 and .3 printing. Recommend %5 rectangular infill. I would avoid 0 bottom layer option,…
Many model railway trees have a very small base with them when purchased. This is my attempt to create a bigger base which means they stand up better and fall over less. Included a model with 4mm interior hole for trees with larger…
The original Reindeer card is a fantastic gift. I found the slot for the Antlers a bit small so I corrected the gap and now they snap together well Print instructions PLA in .15 or .20 seems to work well.
This is two turtlebot3 (Burger and Waffle) waffle plates able to be printed together. The 3mf file is included because it can be difficult to print well. Support enforcers are used. Printed in PLA .3mm layers.
This print is designed to press fit onto a 12V car battery terminal to cover the exposed metal parts of the post to prevent accidental short circuits. This model allows for protection of N70T type posts which are often found on Deep Cycle…
The MkII Wind Turbine from 3dprintable1 is an excellent model but have taken to upgrade some of the components. The original plans files are found at: https://www.thingiverse.com/thing:2060281 The first change is the crank arm which holds…
This model allows you to store cutlery (knives, forks, spoons etc) for drying next to your kitchen sink. Could also be used in the bathroom if the drain plug
The Endless Gears Busy Board model is fantastic. I found that as I had printed the base board with .300mm layers, the interior holes were tight for the gears. I took the 48 tooth gear in the set and scaled the pin down by 5% and also made…
The Original Up Mini 3D printer from Tiertime has a direct drive extruder design and the E-Axis motor gets quite hot, making PLA printing troublesome. This model allows for Noctua 40mm x 20mm fan to be attached to the extruder assembly to…
This model allows you to mount a Turtlebot3 waffle plate on your WaveShare Jetbot robot. This then allows for the mounting of additional sensors includeing lidar, imus etc. Designed to print without the need for support. Source:…
These are "1 unit" make and female interconnect pieces for use when the standard "4 unit" parts won't work or take too long to print. Print instructions Category: Robotics
This is simlar to the Robjects concept. The idea is that this is one of a library of shapes that can be printed to help with the physical connection between prototyping components. There will be more shapes uploaded in the future. They…
This block will connect with other Interconnecting Robot Prototype Blocks I have published on Thingiverse. The purpose of this block is not to hold anything but to allow other blocks to be connected to each other. Designed in Blender…
This is one one of securing the connection between IRPB. It works via press fit. Print instructions Category: Robotics
This IRPB is to allow houseing and thus connection of a standard sized servo. Print instructions Category: Robotics
This is an interconnection piece (does not hold an item, just allows other blocks to be connected). This is a riser Interconnection to allow building "up". Print instructions Category: Robotics
The ROBOTIS Turtlebot3 wheels are made with a software tire over a sprocket shaped gear. This can result in robot wobble when the robot moves as the robot is actually rolling a gear and not a circular wheel. To correct this, this print…
This adapter allows for using a 5 Generation iPad with a Bluetooth keyboard designed for an iPad 2. This adapter receives the iPad 5th Generation and mimics the shape of the edge of an iPad2 so that the iPad 2 can be placed in a Bluetooth…
To wszystkie aktualnie dostępne wyniki.
