Liczymy pasujące modele…
A quick grid to test your bed flatness. You can customize the size to be nearly your bed size and the thickness to be your layer height or maybe 2 or 3x the layer height. Quick print that lets you easily see where your bed is not level.…
I needed a flange to pass a 3 inch vent hose from my laser cutter to the outside.
Being basically lazy, I borrowed a DE9 (DB9, but that's not technically correct; a D sub miniature or D Sub connector) from a different design and used OpenSCAD to hack away the part I didn't want, as well as add an apron with mounting…
I bought a cheap 1610 engraver (the LinkSprite, but honestly, I think they are all the same). It had some wing nuts for clamps but it was hard to get things to hold still on the bed. Print 4 of these and use the wing nuts to secure to the…
Customized version of http://www.thingiverse.com/thing:52734 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_thickness = 5 stick_thickness = 3…
I like Chu's bumper, but I needed to mount it at a right angle on a small omniwheel robot. The center hole is covered by the shield socket, but I left it there anyway. You could use it to mount with a flat head bolt before installing the…
Tiny book with a little compartment. The pages go in a certain way: You can probably tell the “ears” on the inside fit inside the grooves in the cover and the ears go towards the spine. This lets you pull the drawer out without totally…
I tried printing the original for a gift but I keep my first layer high because I use BuildTak so the tip just wasn't making enough contact and would warp a little. It wasn't bad but my OCD kicked in and I added this thin ear to "hold da…
Peace out, baby! By tuning the parameters you can make a few other interesting shapes. And, yes, you can tune them so they don't make sense at all. Could probably be scaled to make reasonable earrings if that's your thing. This is an…
Customized version of http://www.thingiverse.com/thing:74322 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: image_file = lithopane20130616-1537-wbqaif-0.dat…
The cap off my cheap broom broke, so I sort of redid it as a CAD model. The original was a little shorter, and had a concave cap under the hanging slot. I made it convex for no particular reason. If the hole is a little tight, you can…
Open the OpenSCAD file and tune for your printer. It assumes your bed is square, but you can always do the short side or scale it in the slicer. It is helpful to set the square count to the number of autolevel points you use. Note the…
This will let you mount a prox sensor (or anything really) anywhere you have a bolt on your X carriage facing up or down. For a prox sensor, the vertical part needs to be enough to hold the part just above where the hot end hits but below…
This is derived from the #6 foot for PCB I made earlier but is customizable. Instructions Fill out the form. Make sure the bolt hole is shorter than your actual bolt so the nut can engage. That's it. You can find tap hole tables on Google…
A rubber band powered PCB vise. Instructions Print two of the end pieces. You can print one set of the pcbvise-support.stl (note: currently untested) or you can use small dowels or pencils through the square holes. Make sure the slots are…
Simple reducing coupling to demonstrate OpenSCAD Customizer. Hackaday post pending. Category: DIY
This is a remix for the quick change X carriage for Anet A8/AM8. The carriage itself is my remix of another carriage that has a part fan and sensor mount.This should fix "standard" plates from the source, however, I had problems with it…
Like most geeks, I have an LED based binary clock on my desk. But, hey, humans are analog creatures so please enjoy my analog binary clock. Based on Achim's clock3 which is great! Instructions Print all 3 pieces and insert a cheap clock…
Great design but hard to print on its side. The holes are inset so I placed a thin roof on the holes so it will print as a bridge. Then just drill those holes out using the non-inset side as a drill guide. Easy. Category: 3D Printer Parts
To wszystkie aktualnie dostępne wyniki.
