Liczymy pasujące modele…
Hi! Here is a dual antenna mount for TrueRC Core 5.8 antennas (optimised for 85mm antennas), to be installed on JeNo 5,1 frame. Print int TPU without support, 20% infill or more. 💡 For full versions, optimized models and more options 👉…
Hi! For my first Drone built, I went for a new TBS source One V5 frame. There is not a lot of 3D part for this frame so far, so here are my arms protection and skid, that are also used for motor soft mount. Print in TPU, 0.2mm layer…
Hi! JeNo 5,1" ELRS antenna mount Print upside down, without support, in TPU 30%infill 💡 For full versions, optimized models and more options 👉 https://cults3d.com/@-kC- 📦 All my designs and more : https://atelierkc.fr
Hi! Here is my design for JeNo 5,1" Flywoo Goku M10 GPS mount Print without support, 30% infill 💡 For full versions, optimized models and more options 👉 https://cults3d.com/@-kC- 📦 All my designs and more : https://atelierkc.fr
Hi! Here is a dual antenna mount for walksnail avatar V1, to be installed on JeNo 5,1 frame Print without support, 20% infill or more. 💡 For full versions, optimized models and more options 👉 https://cults3d.com/@-kC- 📦 All my designs and…
Hi! Here is a mobula 6 HD lightweight canopy, roughly inspired by the Slim Whoop Camera Mount (Adjustable Angle) by MrShutterBug. You'll have to remove the open square shaped part on the camera and re-use its two screws to avoid camera…
Hi! Here is my design for landing skid/ arm protection for the Diatone Roma L3 frame. It also acts as screw spacer to avoid screws touching the motor windings in my case. Holes for 9x9mm motor mount. print in TPU, 100% infill 💡 For full…
Hi! This buzzer holder has to be installed behind the fpv cam, on the standoffs of the TBS source one V5 frame. Print in TPU, 100% infill, no support needed. Edit: Thanks to Talhah remarks on his remix (…
ESC is quite exposed to bottom/side impacts on the TBS Source One V5 frame. I designed this part to protect it sightly better. It also isolate the ESC from the carbon frame. Print in TPU, 100% infill, upside down (flat surface on the…
Hi! Here is a Vifly finder 2 mount for the JeNo 5,1" frame Print without support, 100% infill 💡 For full versions, optimized models and more options 👉 https://cults3d.com/@-kC- 📦 All my designs and more : https://atelierkc.fr
Hi, Here is a VTX dual antennas holder for the JeNo 5.1 frame, to be used with 4mm tube antennas, or linear antennas. Print in TPU, no support needed. 💡 For full versions, optimized models and more options 👉 https://cults3d.com/@-kC- 📦…
Hi! Here is a Gopro 9 (and other gopro of the same size) mount for the JeNo 5,1" frame. Designed to be printed without support, laying on the side (battery bay side). 20% infill or more. 💡 For full versions, optimized models and more…
The "Walksnail Fatshark Avatar Goggle Shim" made by iamnoland is great to avoid dirty lens on the fatshark/walksnail goggle, but his design is slightly too thick for my head: Goggle are tilted down too much resulting in a blurry upper…
To wszystkie aktualnie dostępne wyniki.
