Liczymy pasujące modele…
I don't have or use the larger SD cards, haven't for a while so didn't want all the extra space taken for them. I removed them and made the box a little smaller to just hold Micro SD cards. Remixed from…
There are a number of sunshades for various Lowrance Hook Reveal models, but I really wasn't satisfied with them for one reason or another. Some of my dislikes were multiple pieces, flimsy looking, prevented angle adjustment, and most…
Top glass riser that doesn't take 22 hours to print and I can control the airflow through the riser. Simple, clean, easy to print and suited my needs. Props to the original design.
This knob also fits my Blackstone 36" griddle, so I assume will fit all sizes. My buddy had a Blackstone Adventure 17 griddle given to him, I had one, so pulled the knob off and measured it up with calipers and a depth gauge so I could…
Drive adapter to use a Drill with the V-Spooler re-spooler.
Perfect geek/nerd clock for mathematically inclined, or engineers like me :) Made this for a fellow on Facebook's 3DP Rescue group. There are 2 versions, raised letters for single color printers and flush lettering for multi-color…
Looked at a few replacement legs for a table-top Blackstone griddle and wasn't happy with the options so I created this. It uses an M6 bolt or nut on the inside and is slotted to keep the bolt or nut in position while you tighten it down…
Clean, easy to print top glass riser tested on both P1P and P1S. Added vented slots and a mount in the left inside corner that I use for a camera, can be about anything I expet. Amazon.com : YI Home Security Camera, 1080p 2.4G WiFi IP…
Adapts the V-Spooler standard axle to a DC motor. The motor I used is - Greartisan DC 12V 300RPM Gear Motor High Torque Electric Micro Speed Reduction Geared Motor Eccentric Output Shaft 37mm Diameter Gearbox: Amazon.com: Industrial &…
Loved the design of the ornament, just wanted to add more colors to make it pop. Remixed in a couple ways to allow a unique color on the outside of the ring.
Minnie Mouse Keychain for the Holidays
Published by Matter Hackers (M3D), they published it to OneDrive, thought it would be easier to find here.
I really liked the Euchre scoreboxes by K6klinger, but wanted raised numbers so they were easier to see. I printed the box in one color, the top in another, and the letters in white. Original is https://www.thingiverse.com/thing:5793631 .…
There are a lot of great Grinch Christmas doodads, wanted one with a little different…vibe. Print them face down, ideally with a textured plate.
Remix of the knob so that it's not as thick (tall). This is about 8mm tall. I needed this for a Blackstone 28" Grill Wheel setup to connect wheels to the legs. Print Settings Printer: Bambu Lab P1P Rafts: No Supports: Doesn't Matter…
Slightly taller than the last version, still easy print. Supports use of a Wyzecam2. All of the files are in the .3MF, and depending on your printer you might need to make the screw or nut a little bigger/smaller so they are snug but…
Ever have a perfectly good knob on a Blackstone griddle, but the little center insert piece is broken? Apparently this is pretty common with these knobs. If you need a complete knob replacement, or want to just print your own in the color…
DC Motor enclosure with snap in place lid. Print with only tree supports. The side vents don't need supports, only the two end holes. Motor Controller w/Switch…
For whatever reason, the original wasn't large enough to wrap around the front and the back of my dual-z axis upgrade on my Ender 3 Pro. The space on mine is about 60mm.
Wanted a toolbox that faced forward. Was a little concerned the two corner screws weren't going to hold it, but they are plenty rigid. The holes are countersunk, but I only had barrel headed hex screws (M3x12) that worked fine too. I was…
Tried to create the original, and the clips at the end of the traversal screw broke every time I tried to insert them. Tried a couple materials, no go. Remixed to that the long traversal screw has an inset thread which a smaller screw…
Props to the author for a nice spool guide. I made the rear main arm a little less rounded to let me print it without supports. Also modified the gear assembly with the lateral long arm so that I could adjust the angle of the long arm to…
Wanted to create a night light that I could exchange the diffuser for sports teams, holidays, lithophanes. etc. Any diffuser that is 88mm x 88mm will work which means people aught to be able to use just about anything going such as those…
To wszystkie aktualnie dostępne wyniki.
