Liczymy pasujące modele…
Just a small cup to mount on a pegboard to hold small items like screwdrivers. Edit: Added a second bigger model due to several requests. I had initially made the cup smaller to fit very snug and secure into my pegboard so I didn't risk…
Used a previous design as a base for the blank, but added a custom. fitting for the USB cable from the T10 head unit. Bracing put in the back so the cable doesn't push through when trying to attach a USB device. Cable holds in place by…
Working on a project at work, I needed a place to store multiple androids, iPhones, and iPads while they are being imaged and set up. This is a stand to keep all these devices accessible while trying to keep my desk as organized as…
This is a remix of https://www.thingiverse.com/thing:3501775 I take no credit for the design. Dexcom recently changed the size of the patches used, and the original design started causing me skin irritation. I simply cut the ends off of…
This can work in either orientation. 60 degree angle from doorbell wiring. Category: Outdoor & Garden
The most common failure in the Parrot Jumping Sumo is the jumping mechanism. This is a replacement wheel that will get your sumo jumping again. Instructions I printed this in ABS, upside down, with support, at 75% infill to give it a…
I wanted to mount my rear speakers high up, but angle them downwards. This is a nice and sturdy mount that uses the existing mounting hardware that screws into the back of the speakers. Category: Electronics
This stand uses two Anker qi chargers found here: https://www.amazon.com/Anker-Wireless-PowerWave-Upgraded-Fast-Charging/dp/B07THHQMHM It is designed so the phone can charge in either portrait or landscape orientation. Designed to be…
based off cmc10001's design. I wanted to reuse the holes created in the original mount that came with the Tekonsha P3. I also had issues with the arms being slightly too close together, and not quite long enough after adding the lip at…
Wall mount for maglite with C cell batteries. Category: Organization
Remixed case to add print in place hinge. You still need the TPU inserts from the original design.
I don't like searching around in my pockets trying to find these. With this organizer, they are always in the same place every time. This also protects the dial on the chapstick which helps prevent wasting chapstick.
A remix of the pocket organizer. I added a place for the airpods charging case, and resized the drawer so I could keep mints. I increased the size of the handle for the drawer to make it easier to open too. The small bend in the design is…
Just a quick holder to attach to the side of the IKEA Hemnes nightstand. Use supports at the top where it actually attaches to the table. I used a 3M command strip just to secure it to the side in case it got bumped. But the fit is nice…
Remix of my 2 raspberry pi tower. This fits in 1U of rack space. use the faceplates from the original tower model from here https://www.prusaprinters.org/prints/137568-raspberry-pi-23-tower Category: Computer
I had a Pi Zero PoE hat that I wanted to rack mount. Holes created for ventilation including a hole at the top for the heat sync on the Pi Zero. This is a remix based off the model by M_R_P on thingiverse.…
I made two small adjustments to Gonzoop's design. The weight of the camera made the original deform outward slightly, so I sealed up the sides to make it a little sturdier. I also changed one of the screw holes into a slot to make it…
Very low profile mount that uses a wooden dowel rod as a curtain rod. This is meant to cover the window on the door of our RV and fit in the very small gap between the door and the screen door. This uses the 1 inch 3m double sided squares…
This is a mounting arm for the Raspberry Pi camera for monitoring prints and taking timelapse videos. Category: 3D Printer Parts
To wszystkie aktualnie dostępne wyniki.
