Liczymy pasujące modele…
A handy soap box for traveling work, or gym. Print notes.. The Latch needs to be printed precisely. Printing at a 0.15 layer height, using a 0.25 nozzle yielded a part that moved freely directly from the print bed. An 0.4 nozzle should…
Fairly discrete gpu support bracket. Adjustable Print Settings Supports: No Resolution: 3 Infill: 40 Filament: Prusament PETG Category: Computer
Shower corner shelves. Make singular or as shown with a floating shelf. Optional soap dish, needs to be glued into place. Installation using two screws only. Recommended print setting. Supports - Not needed Layer hight - A 0.6mm nozzle at…
I liked the look of a lot of the other face plates but found them all to balky.
For a cool effect, add a color change at 1mm.
Rc plane ceiling hanger for planes up to 1500 mm wingspan. I used medical bungee cord that I had left ever for hanging. Print Settings Resolution: 0.2 Infill: 20 Filament: redline PLA Category: Hobby
Miniature Billiard, Pool table. For use as prop, miniature etc.
A Japanese inspired knife display stand. Prints in two parts An m3 nut bolt and washes are required for assembly. Supports are not needed 0.2 Layer height or better recommended with quality settings
Model is sized to be printable on a mk3, using all available print bed space. I used an 0.8 nozzle and 0.55 layer hight, took about eight hours to print.
Allows up to 60mm clearance for sound dampening inside the enclosure. Has a huge affect on the noise level of printing. I used scrap drywall witch was 13mm thick, have added alternate sizes for different material sizes. Print Settings…
A basic shower head holder for the bath, Improved for strength as first design broke too easily V3 needs 12mm washers. Will increase strength from v2, made this change after one of mine broke around the screws from too much abuse Print…
This is a handy hand held shop vac, using readily available rc parts. Has lots of power. Works best with two cell lipos. Electronics needed. 40mm edf impeller 30 amp speed controller Servo tester and on/off switch Two or three s lipo…
Basic Valve cap with optional TPU sealer insert. Update 4/26/20 Fixed thread Print Settings Resolution: 1.5 Filament: Prusament PETG PETG Black Category: Automotive
The toothbrush section screws into place. The cradle slots in and is easily removed for cleaning I printed the toothbrush holder section without supports and it came out fine.
A handy tray for working on radio controlled models. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.16 Infill: 15 Category: Hobby
Both work well. Antenna guides can be resized to the desired length by adjusting the z-hight in the slicer program, also need to be glued to the base. I used a strip of the supplied double sided tape to attach to the boom. A magnet is…
Lite weight tray style holder under three grams yet provides a stable platform Updated to a lower profile design Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: 0.2 Infill: 15 Notes: Might want to…
Was a bit disappointed with the less than stellar stock lens tray, so I designed this for the astro community. The screw hole spacing is the same as the original lens holder, except for the middle screw witch is offset. Outer hinge pin…
Hiking/travel knife case. Made for the popular Victorynox and similer sized knives Has inserts for Four 10x2 mm Neodym Magnets. Print Settings Printer Brand: Prusa Printer: I3 MK3S Supports: No Resolution: 0.2 Infill: 15 Category: Sport &…
A nice easy printable wall hanger set for your headphones. Print Settings Rafts: No Supports: Yes Resolution: 0.2 Infill: 15 Category: Audio
A must have to protect the receiver along with the week cardboard shell. Mine was a perfect fit so probably wont need size adjusting. Print Settings Supports: No Resolution: 02 Notes: Print antenna holes down Category: R/C Vehicles
Needed 52 mm 4mm screws 4 washers 4 nylock nuts.
Printed using 0.6 nozzle with a 0.35mm layer height. Print time ca 1h.45min
A super simple antenna guide, for any RC receiver Can be mounted using hot glue or double sided tape, Print Settings Resolution: 0.2 Notes: Simply rescale antenna guide in the Z direction for desired hight. With the boosted dipole antenna…
To wszystkie aktualnie dostępne wyniki.
