Liczymy pasujące modele…
I have a Bostitch MIIIFN floor nailer that is setup for ¾ inch hardwood. A friend wants to borrow it to install ½ inch flooring. There is a baseplate that needs to be changed to allow the cleats to strike the flooring at the junction of…
Printed with PLA at 100% infill to optimize strength. Each clamp uses a #8-32 x 1 inch machine screw and nut to attach to trekking pole. G-Code file prints both female and male clamps for Ender 3v2.
Antlers, skull and stand are printed at 20% infill. Hinge, year numbers and number base are printed at 100% infill. PLA is used for all parts. Antlers and skull are printed using egg shell colored PLA, with antlers painted with acrylic…
Kiri Engine scan of my 2022 Whitetail buck antlers. Cleaned up in Meshmixer and merged with skull from KoekMaker98 on Thingiverse: thing:4021358. Stand is modified from Model Airplane by ichdruck3d on Thingiverse: thing:198954. Skull and…
Primarily used by handicapped or senior curlers for rock delivery without having to go into a “crouch”. Attaches to curling stick using standard broomstick/paint roller thread (ACME ¾ inch diameter 5 TPI). Goal was to use only plastic…
A few years ago I found a moose antler shed in the woods of Northern Alberta. Inspired by the art of Steve Kerr https://stevekerrartist.com/art-work/moose-antler-paintings/ , my wife decided to try her hand at painting a scene on the…
Needed a mount for a Chipolo Pop and nothing seemed to fit. This is a mod of Onshape Public "Chipolo Bottle Holder" that was sized for a smaller Chipolo one spot. The original design also had a curved bottom to fit a rounded downtube.…
Wonderful Job on the original by Immaculato solving the big problem of the Caldwell unit being a magnet for bullets and self destructing, however, every time the sacrificial reflector receives an impact it has to be replaced with a new…
Sports Afield gun safes come with 3 standoffs to accommodate storage of firearms with optics. In most cases more are needed. This print uses #6-#8 1inch drywall anchors cut to 0.7 inch (17.75 mm) to allow plugging into the safe's support…
Local curling club required a trophy for their stick curling league. Used an existing trophy as an example, but used the Makerlab “image to 3d model” tool to create the body of the trophy from a photo of an actual curler. The rest was…
This is a laser trainer using 3D printed components with electronics self contained in a barrel mounted configuration. My goal was to create a laser trainer that could adapt to a variety of long rifles that would not require readjustment…
Replacement gasket for cherry pitter. Printed at 100% infill, 0.1 mm layer height with TPU filament.
Needed to replace a broken wooden chair rung and couldn't find a matching piece. I don't have a lathe nor know how to use one so I created a hollow wrapper in Onshape for a 5/8 inch hardwood dowel available at hardware stores. Printed the…
In addition to the printed parts identified, this model now requires two steel "pen springs" to push against the plungers. The springs are of 0.5 mm diameter wire, with a spring diameter of 6mm and length of 40mm with 20 turns over the…
Wanted to display this race sticker in a better way than my car bumper and have a race souvenir. Printed the moose in PLA at .2 mm layer height, and 20% infill, brim, no support- back of moose on print bed. Wheel was printed at 100%…
Lost one of the tools for flipping the cleats on winter boots. The tool fits in a handy pocket on the side of the boot. Pictures show original tool on the left and printed replacement on the right. Used with Kunitz spike boots or similar…
To wszystkie aktualnie dostępne wyniki.
