Liczymy pasujące modele…
Mount a sharpie inside a drawer that will automatically present itself for quick access. Simple lever mechanism will lift and lower the sharpie when the drawer opens and closes. Easy one-handed operation! Update 2022-08-27 New version of…
I tried a few existing models for hanging my tweezers and decided to make my own variation. Nothing groundbreaking, just a style I preferred. I printed mine in PETG, .2mm, no supports.
This is an alternative peg for the Modular shelving system. The original peg was very tight on my printer and required some hammering to get into place. They were also very hard to remove without damaging the containers. This peg is just…
I've seen a few nice designs to mount UniFi equipment but nothing for the TP-Link Omada line. I made this specifically for my home networking setup. Holds the following equipment: Omada Gigabit VPN Router (ER7206) Jetstream 8 Port Gigabit…
This is a simple cover to protect the surface of the 13" Framework laptop. I designed this to be thin, easy to attach and remove, and printable on my MK4. Two version of the center piece are included. One solid and another with a hole to…
Just a basic stand for the Wowstick and 8 bits. Based on the Gridfinity Refined set for press fit magnets and center thumb screw. Holes are oversized for a loose fit and quick access. Modeled around the Wowstick 1F Pro model. An alternate…
Holds a standard size pellet tin vertically for easy identification. I was tired of looking at stacks of tins and wanted a way to find more easily the one I want. I created an extender that can be combined with the holder to make Tins in…
I picked up an Iris CE from Keebio as my first dip into split keyboards. It didn't come with any tenting options so I made this simple stand to experiment. It's designed for the Aluminum case but I imagine it'll work for the Polycarbonate…
I designed this saddle style mount that attaches to the top pic rail and holds the two included magazines for the Weihrauch HW 44 PCP pistol. Printing Nothing special, I printed in PLA with no supports. Assembly Glue a Mag Clip to each…
I really liked this design from gatapass but I wasn't a fan of the sharp points and thick base. https://www.thingiverse.com/thing:4239021 Here is a version I made in the same basic style but with liberal use of rounded corners. Category:…
For mounting a Raspberry Pi camera on the side pillar of an Anycubic Mega without the use of glue or other materials. I borrowed the clamp from dasbossy's pi mount.. https://www.thingiverse.com/thing:3057389 .. and wengeol2's camera…
I designed this custom pistol stand for the Weihrauch HW 44 PCP. Build Cut the base and fence from 3mm plywood and glue together. Cut the vertical prop from 3mm acrylic. Print the Connector. I used PLA with no supports. You should be able…
I wanted a quicker way to switch between a flashlight and IR light for night time ratting. I made this magnetic mount for holding lightweight picatinny accessories to the barrel of my air rifle. The mount is modeled for a 50mm diameter…
I was recently making Bristle Bots with my niece and decided that a little over-engineering could enhance the experience. These bots are normally held together with some double sided tape for both structure and electrical contacts. While…
The Sony Xperia 1 II goes on preorder next week. I like the design and the specs but was unsure of the form factor. This phone has a 21:9 aspect ratio which makes it taller than most. I made this model as a stand in so I could see if it…
The stock panel plug was causing the PTFE on my setup to bend too sharply on the bottom side, causing frequent loading failures. I added bowden bends to both the top and bottom that can rotate freely. I've been using this for a couple…
Instead of re-printing the ptfe-guide parts with the MMU and dissembling/reassembling the unit I made this simple label plate that just sticks to the outside and is a fairly quick print. Confession: I assembled the unit in the wrong order…
Simple stand to hold the B-robot EVO2 / BroBot upright for display. B-robot EVO 2 https://www.thingiverse.com/thing:2306541 Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: .3 Infill: 10%…
To wszystkie aktualnie dostępne wyniki.
