P
PrintablesVerris
Hadley Mirror Cover Stacking
Added a slotted handle for the cover so you can stack the original and web cover. Additionally you can add the bhatinov mask as well.
- Pobrania
- 221
- Polubienia
- 17
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesVerris
Voron 2.4 Carbon Gantry Z Cable Mount
Mounts for the Chaoticlab CF gantry on the 2.4 (And probably trident) to route your wires using a standard tape measure covered in cable wrap. There are 4 M3 heat inserts on the back of the inner bottom bracket, and two on the face, two…
- Pobrania
- 109
- Polubienia
- 59
- Ocena
- 4,5
P
PrintablesVerris
Repwinder - Shortened End Caps
I've shortened the end caps for the repwinder. For the locking screw version, I removed the ratchet as that should only be needed on one side. I then shortened it by 0.8mm. For the other end, I also shortened it by 1mm, and left an indent…
- Pobrania
- 82
- Polubienia
- 5
- Ocena
- 5
P
PrintablesVerris
Hadley Mirror Cover Holder
Storage for the two mirror covers (One of my modified slot cover, listed as a remix), the web cover and the Bhatinov mask. Attached via #6 ¾" screws. Printed with 0.6mm nozzle at 0.35 layer height, 15% infill.
- Pobrania
- 79
- Polubienia
- 6
- Ocena
- 5
P
PrintablesVerris
MPCNC Control Panel
This is a control panel for my MPCNC. It requires pretty specific parts which I have listed below. Main Panel Connectors https://www.amazon.com/gp/product/B07HM58GWD/ 2 Latching (Enables) and 1 Momentary pushbutton…
- Pobrania
- 66
- Polubienia
- 15
- Ocena
- 0
P
PrintablesVerris
Carvera M6 ULP Risers
Modified Fae's risers to allow for M6 ULP screws with the SMW fixture plate.
- Pobrania
- 61
- Polubienia
- 7
- Ocena
- 0
P
PrintablesVerris
Voron 2.4 Alternate Z Chain Bed Quick Connect
Quick disconnect cable for the voron 2 bed heater, thermistor and ground wires
- Pobrania
- 56
- Polubienia
- 24
- Ocena
- 0
P
PrintablesVerris
Fillamentum Spacer - Repwinder
Spacer and end cap for fillamentum spools for the repwinder Print instructions 0.2mm, 15%
- Pobrania
- 48
- Polubienia
- 5
- Ocena
- 5
P
PrintablesVerris
MPCNC Primo 55mm Spindle Jtech 7W Laser Magnetic Mount
Adds holes for a magnet and the two pass through bolts for the Jtech 7w Laser with the magnetic mount. Lets you easily clip the laser on and off with the magnets without removing the spindle. You will need 4 8x3mm magnets…
- Pobrania
- 44
- Polubienia
- 3
- Ocena
- 0
P
PrintablesVerris
Filaments.ca Spacer - Repwinder
Spacer for filaments.ca spools for the Repwinder Print instructions 0.2mm, 15% infill
- Pobrania
- 31
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.