P
PrintablesFunctionOverForm
Flower Pot Base
A base for a flower pot, to stop water from leaking out. Scale X and Y to fit your needs.
- Pobrania
- 729
- Polubienia
- 70
- Ocena
- 4,8
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesFunctionOverForm
PC Case Stand
Raises a computer case off the floor. Great for if you are setting your case on carpet and have a fan on the bottom of your case. I used PLA and recommend using 20%+ inflill. You will need to print two, one for the front and one for the…
- Pobrania
- 109
- Polubienia
- 7
- Ocena
- 5
P
PrintablesFunctionOverForm
Paintball Freak XL Insert Case
Freak XL insert case. Fits four inserts. Uses eight 6X3 mm magnets to hold the lid on. Use a little bit of super glue to hold the magnets in. They should be snug, but not hard to push in. They are not meant to be friction fit. I used ABS,…
- Pobrania
- 39
- Polubienia
- 3
- Ocena
- 0
P
PrintablesFunctionOverForm
Dye LTR Paintball Loader Speedfeed
This is an alternative to other speedfeed options for the DYE LTR. It allows you to run a speedfeed and still open the loader fully for loading/unloading. Similar to how the spire/ctrl/r2 loaders function. You can use normal LTR…
- Pobrania
- 36
- Polubienia
- 6
- Ocena
- 0
P
PrintablesFunctionOverForm
BMG-M and Mosquito Hotend RHD Mount
This mount works for PrinterMods MDD, BMG-M and Mosquito Hotend, with a RHD Fan Duct by RH_Dreambox. The duct is the "RHD Fan duct for MK3 Bondtech BMG Mosquito" https://www.thingiverse.com/thing:4217188 Print instructions I designed this…
- Pobrania
- 25
- Polubienia
- 0
- Ocena
- 0
P
PrintablesFunctionOverForm
Smart Parts Impulse Paintball Marker Grip Panels With Display
Designed to fit the Morlock MK4 board with display and battery. I used a piece of polycarbonate to hold the micro switch and protect the display. Switch is an Omron D2F-FL. I recommend using a high impact filament like Polymaker PolyMax.…
- Pobrania
- 7
- Polubienia
- 2
- Ocena
- 0
P
PrintablesFunctionOverForm
Smart Parts Impulse Paintball Marker Tray Board
This a replacement for the circuit board in the a Smart Parts Impulse. It gives points to mount the micro switch for the trigger and a micro switch for power in a dwell button cut out. I am using a Morlock MK4 and the micro switches are…
- Pobrania
- 6
- Polubienia
- 0
- Ocena
- 0
P
PrintablesFunctionOverForm
Dye DSR+ / CZR Feedneck Thumbscrew
Replaces the feedneck adjustment screw with a tumbscrew. The screw head should fit tightly and may need to be pressed in. Uses a SHCS #8-32x1" screw. I used a Hillman that I got from Ace Hardware.
- Pobrania
- 6
- Polubienia
- 0
- Ocena
- 0
P
PrintablesFunctionOverForm
Triglide Dual Strap
Used for holding a headband tight on your head.
- Pobrania
- 1
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.