Liczymy pasujące modele…
faucet garden adapter 4 variants M22x1 faucet → quick coupling for hose M22x1 faucet → 1" ¾" & ½" outer thread use 6x3mm or similar gasket for quick coupling Print settings 5 walls 0.1mm layer 30% infill no supports
The fine thread M22x1 is often used for in house water taps. You need in addition a O-ring and a rubber gasket for the connection between adapter and the water tap. Printed with 0.12 layer height and in PETG.
Support is necessary, even if the pot and feet are printed separately. However, both parts must be glued together. A model has also been added where everything is in one piece, support is required here, too.
Small Wiring Junction box 22x15mm to fit 2.5A terminal strip with two connections.
Kitchen organizer Box 22x22x10cm I use it for car slleping build Print settings 0,2mm layer 5 walls 15% infill no supports
Bicycle crank cap m22x1 Print the model as it is loaded - you need to enable supports in the slicer. I used ironing when printing. I printed from PETG Nozzle 0.4 Layer 0.12 Minimum 5 walls CONCLUSION 💚💚💚If you enjoyed the project please…
Printet with PLA+ a connector between faucet and an adjustable Dual Mode Sprayer
It's a small, simple and quick print. Normally you need two sleeves for a door.
This model is an adapter that connects a garden hose connector of standard size M32 with 2 mm pitch to a standard size M22 sink thread with a pitch of 1 mm. Use a rubber gasket with an outer diameter of 18 mm inside the adapter to make…
Used on a kitchen faucet. Attention! - The part can be printed without supports - placing the external thread closer to the table. But in this case, there are problems with adhesion to the bed. For this, I added an additional cross that…
Kitchen cutlery organizer Box 22x22x10cm I use it for car slleping build three areas for organising cutlery and other kitchen tools Print settings 0,2mm layer 5 walls 15% infill no supports
It works fine, but as the water contains no air it splashes too much back up when it hits the sink I used variable layer height and 0.12 for the threads,the rest is 0.2 Printed in green Clas Ohlson PETG
This shower faucet addon came out pretty good. Its actually what I wanted. The nozzles are directed to a center point 400mm below the faucet outlet so the water beams flows almost perfectly straght down. Print in PETG to ensure it will…
I needed a panel Nut for my potentiometer. I couldn't find any special models that met my requirements, so I made it myself, and maybe I can help someone with it. It's not fully screwed on because it has a recess for the potentiometer…
Eine Abdeckung für einen 22x10 Kabelkanal
This is a simple yet effective adapter that converts a G3/4 (26.4mm) faucet thread to an M22x1 (22mm) thread. It is ideal for connecting various accessories such as aerators, water filters, or hose adapters to your faucet. The design…
Description This model was designed as a simple way to extend the functionality of a bathroom ladder radiator. These radiators often lack convenient places to hang smaller items like towels, shirts, or underwear. This snap-on holder adds…
This is an axle thread cover I made to help prevent rust when my vehicle is running winter tyres. This cover is for an M22 x 1.5mm thread. I recommend using PETG for this part. My experience is they tighten up nicely against the inner…
Endcap for M22x1,5 thread. I made this to protect the threads and the internals of my pressure washer attachments. Printed in PETG with 15% infill. Model should have enough clearance to screw on, scale if it's too tight for you.
Adapter M22×1 male to G1/2 BSPP male – 12 mm bore
Raccord à rotule pour robinet Ø22 x 1 mm avec mini pommeau imprimable Ø50 mm. Inclinaison nominale 0 à 25°. Grille démontable : 61 trous de Ø1,2 mm. COMPATIBILITÉ : vérifier une sortie mâle Ø22 mm, pas de 1 mm et environ 5 mm de filetage.…
M22 × 1.5 thread +0.40 mm built-in tolerance 17 mm standard ball joint 17.6 mm hole size for the ball to pass through 29.0 mm outside diameter
Just a strong box with a size of 22x17x7,5cm I print it with PETG 3 perimeters and 40% infill But u can use any material you want You need a 22,5cm 1,75mm filament string for the hinge
——————————————— Deutsch ——————————————— Einschraubbarer Trichter für Ölwechsel Diesen Trichter habe ich selbst konstruiert, um den Ölwechsel an den Achsen meines Kramer 312LE deutlich zu erleichtern. Bisher musste ein normaler Trichter…
22x1mm to 26x1.75mm (3/4") adapter - sink to garden hose For taps with a 22x1mm male thread. You need a standard 3/4" quick coupling to connect the garden hose.
Foldable wall mount designed specifically for the Byintek projector (dimensions: 22 cm width, 15 cm height, 20 cm depth). Printed in PETG using a 0.4mm nozzle . Requires supports on certain parts (I used organic/tree supports). Assembly…
Description This model was designed as a simple way to extend the functionality of a bathroom ladder radiator. These radiators often lack convenient places to hang smaller items like towels, shirts, or underwear. This snap-on holder adds…
——————————————— Deutsch ——————————————— Einschraubbarer Trichter für Ölwechsel Diesen Trichter habe ich selbst konstruiert, um den Ölwechsel an den Achsen meines Kramer 312LE deutlich zu erleichtern. Bisher musste ein normaler Trichter…
This model is an adapter that connects a garden hose connector of standard size M32 with 2 mm pitch to a standard size M22 sink thread with a pitch of 1 mm. Use a rubber gasket with an outer diameter of 18 mm inside the adapter to make…
https://www.printables.com/de/model/224068-beer-bottle-holder-for-pool-surround-bierflaschen-
