Liczymy pasujące modele…
“Years ago" Inspired by all kind of clever solutions at the time, I designed a dispenser for 330ml cans which printed in only 4 pieces on my BIG 3D printer (~450mm x 450mm x450mm) which rests in piece ;-( Luckily the local brewery decided…
A friend needed an adapter to try out a 65mm spindle in the existing 69mm spindle mount on his small CNC router, so I drew one up and printed it. Prints upside-down on the flange so you don't need any support.
Here's links to the things I got on amazon to put in the slot at the bottom, and optionally reinforce the screw hole. The screws used were the ones that came with the CNC, but it's a 5mm threaded screw hole in the model, so any m5 should…
This is a tall M42-screwmount rear lens cap styled after caps paired with PL-Mount cinema lenses. It was designed to fit a Meteor 5-1 f/1.9 17-69mm 16mm film camera M42-mount lens (typically found paired with the Krasnogorsk-3), which has…
For our old Zeiss lens set, I created focus rings in different sizes. So this is a selection from 58mm inner diameter of the ring to 69mm in 0.5mm increments. (2,28 inch to 2,72 inch) Measured is the inner diameter that has contact to the…
This is a custom dust boot for the Genmitsu 4040 Pro CNC with a 69mm router upgrade. The dust boot in mounted to the Z-axis carriage, so it will not interfere with the router during tool changes. Assembly manual and BOM on our wiki below:…
Customized version of https://www.thingiverse.com/thing:2594893 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2594893 Instructions Using the following options: comp_size_deep = 69 comp_size_x = 136…
This is a taller spindle adapter made to take up the full 60mm height of a Genmitsu spindle mount. The existing adapter I found was shorter, and I wanted more bearing surface for the mount to clamp around the spindle.
PLA Füllung 20% Schichthöhe 0,3mm mit Stützen, ohne Rand
I got tired of switching the entire mount when I wanted to switch spindles on my Genmitsu mill. This is designed for a 52.5mm spindle to be adapted to a 69mm spindle holder, so you can switch from the small spindle to a large commercial…
Remix of the cylinder for the Ikea 365+ 10.6L Spool Holder Filament Dry Box
Bonsai pot 30 hexagonal beveled 182x182x69mm, no support is required if pot and feet are printed separately. However, both parts must then be glued together. A model has also been added where everything is in one piece, support is…
A simple “Drop over” Bahtinov mask for camera lenses under 69mm. (Half of my lenses work with it.) Place over your lens and focus on a star until the | splits the X. https://en.wikipedia.org/wiki/Bahtinov_mask Pattern generated using:…
Plunk your 40W laser into your 69mm router holder. No need to remove brackets requiring retramming each time. I used PLA, and haven't tested it while running the laser so heat issues might be a problem. Print two obviously. I used about…
On the design: Holder diameter is 0.5mm higher than bottle diameter for perfect/easy fit.
Uchwyt mocujący rurę spustową ośrednicy 69mm do ściany ocieplanej styropianem. Wydrukowany przy użyciu filamentu ASA. Drain pipe wall mount for pipe with 69mm diameter. Printed with ASA filament. Szczegóły wydruku/Printing details…
Multi-Size Ring Template 50mm-69mm Want to check your ringsize? Youll likely find it here. Standard printing options. Print in PLA 0.2mm Layerheight
In dieser Version sind die Mulden ca. 69mm weit, um auch andere Streuer aufzunehmen.
Lid and pad holder for the rectangular ink pads
This is to tighten and loosen a large nut from the flush valve that clamps it to the toilet tank. The nut is 69mm wide. Print it in PLA+, PLA-ST, PLA-PRO, and it will be more than strong enough for the job. You can loosen and tighten the…
The same version in https://www.printables.com/model/29457-ikea-platsa-spool-holder-v2 But this time a little shorter. This time is 69mm width. It has less material in the base. Perfect for Bear Frames that are a little wider than…
69mm outside diameter pvc pipe (standard drain pipe) feeder suitable for smaller caged birds (Finches, budgies etc.). Feeder is approx 125mm deep x 100mm wide x 30mm high. Baffle STL. file is used as a bung on the bottom of the pipe to…
This is kind of a Remix of: https://www.thingiverse.com/thing:3417593 Shortened the Spool Holder, because I don't use 2,5kg spools and better needed some more space in the Enclosure after upgrading to bear frame. Printed in PETG with 3…
Set the MMU3 injection moulded spool holder width for 3DQF 69mm 1KG spools. Due to clearances this is a set before and remove for use tool. 0.2mm layer, speed, 10% gyroid, text facing down https://buymeacoffee.com/warp10
Set the MMU3 injection moulded spool holder width for Prusament 69mm 1KG spools. Due to clearances this is a set before and remove for use tool. 0.2mm layer, speed, 10% gyroid, text facing down https://buymeacoffee.com/warp10
