Liczymy pasujące modele…
Easy Install version Snap-On set of bed sheet aligners. Compatible with factory bracket, Also Strain Relief & Cable Chain Anycubic Cable Drag Chain Anycubic Strain Relief PETG Print with 15% to 20% infill. Left Mount needs support:…
Back Left Mount V3 Now compatible with Cable Drag Chain OEM Strain Relief Installation: 1, Hook the bottom corner under bed of OEM bracket first. 2. Hold the corner you hooked bring it around the bed. 3. Then press down on top of bed…
Back Left Mount v2: includes 2 different options for mounting. (updated 11/29/2023) One with larger holes for M3 heated inserts. One with smaller holes for a through bolt to add a locknut. Can be used with or without a strain relief. Back…
I was inspired by the " Dental guard box " by KeepTheBOX , however I wanted a few changes so I redesigned one from scratch. Main differences: This one is smaller, has shorter bridges in the hinge, no filet on the underside, thicker…
Orthodontic aligners removal tool - Remover per allineatori ortodontici Now available in an enhanced ergonomic design for greater comfort and ease of use. New & Improved: Redesigned for better grip, smoother edges, and effortless aligner…
Simple alignment clips for helping to hold the board tiles together, in case you have warped tiles. Works for both Frosthaven dungeon tiles and the Frosthaven campaign map as they have the same thickness (2mm) Hex aligner version is…
This has been requested a few times so i decided to post it. It does fit a little loose, but it works. I do not have this printer anymore so I cannot make the adjustments.
It always bothered me that you can't align the magnetic print sheet on the magnet very well on the V-core 3. With those small prints you can now. They are simlpy slid on the back edges of the Bed plate and clamp themselves into the unused…
Just a simple PEI sheet aligner for the Anycubic Kobra 2 Plus. The aligners are bolt on to the bed. Remove the bolt on the top right and top left of the bed and take out the buses (be carful with the foam) puss the Buse in hole of the…
You can use original screw holes in the bed platform to mount those. I used self tapping screws, after drilling screw holes to 2,5mm (in the printed part). You could also use hole compensation parameter in the slicer (Orcaslicer has it…
Orthodontic aligners removal tool - KIDS LINE Key Features: New & Improved: Redesigned for better grip, smoother edges, and effortless aligner removal. For continuous use, it is preferable to use an antibacterial filament. For single-use…
Pick tool for removing clear dental aligners/braces.
These are Zenpy's Frosthaven Map Aligners; I just added some little tabs to them to make them easier to print. Each piece has 4 little tabs that will help it to attach to the bed during printing; afterwards, just snip them off and you'll…
Side and front caps for the Prusa XL that cover the holes on the bellows so they don't leak heat through the hex holes. Also aligns the bellow so it doesn't go all over the place. The alignment is defaulted to be the right side sticking…
Storage box for 8 pairs of aligners, spaced 15mm.
I printed them in ASA and at an angle to provide the best strength. I laid it on the corners so the flat edge of the bottom and tip of the top touch the bed. Just used minor tree supports.
This is a remixe of https://www.printables.com/model/1103052-pick-tool-for-dental-aligners. I made an eye for better grip. Printed with ASA, layer 0.2 and 60% infill.
Orthodontic aligners removal tool - KIDS LINE Key Features: New & Improved: Redesigned for better grip, smoother edges, and effortless aligner removal. For continuous use, it is preferable to use an antibacterial filament. For single-use…
