Liczymy pasujące modele…
This project contains a set of 3d printable main side frames and lower frame for a BLue Robotics Bluerov 2 Remote underwater Vehicle https://www.bluerobotics.com/store/rov/bluerov2/ At the time I created these STL copies of the real frame…
This polycarbonate fairing can be used on the BlueROV2 to protect the Subsea Buoyancy Foam . *Please note: 3D print does not include the following: 4 x #4 – 3/4 screws
This polycarbonate add-on fairing is used on the BlueROV2 Heavy configuration to protect the added Subsea Buoyancy Foam and maintain a sleek, hydrodynamic design. Please note that this product doesn’t do much when used alone – it’s meant…
To post process I put a piece of 400 grit sand paper on a sheet of glass and wet sand the mating faces until flat. Apply mold release. You can use vaseline thinned with a bit of mineral turpentine (mineral spirits) in a pinch.
This is the 3D model of a BlueROV2, as used in the virtual double view in BlueOS, but with the wires removed, brackets thickened, and internal voids filled. The geometry is very rough since I made all the changes manually in PrusaSlicer,…
This HDPE thruster guard is used on the BlueROV2 Heavy configuration to protect the vertical thrusters and to prevent them from snagging on the tether, weeds, or ropes. *Please note: 3D print does not include the following: 8 x Heavy…
If you only need sonar imaging of what's in front of the ROV and wish to remove the sonar from a more exposed position above the ROV these are an option to mount on either electronics PODS.
Allows the use of an Arducam camera module with Bluerov's Subsea Camera Tilt System . Or really any project where you want to use an HS-5055MG servo to move an arducam around. The inside of the mount point is not splined (like the servo's…
A fairing for protecting the ping360 on Blue Robotics BlueROV2 Heavy
We love using the DVL A50 on our @BlueRobotics BlueROV2 Heavy but I didn't like how we had to drill into the frame to mount the sensor. I therefore designed a mount that uses existing bolt holes in the frame to mount it. I printed it at a…
A mount/fairing for mounting a 2 inches enclosure on top of a BlueROV2 Heavy. designed for using zipties
A custom mount to place DeepWater Exploration exploreHD USB Camera on the BlueROV newton subsea gripper. To be used by printing two of them and combine each other with M4 screws. The mount for the camera uses M3 screws and to be used with…
A forward facing ping sonar mount to be used by BlueROV2 Ping Sonar Altimeter and Echosounder. The screw uses the default screws for battery enclosure and the original ping mount. It is located slightly to the upper side of the battery…
This might be useful if you're building a smaller ROV based on BlueRobotics parts. The front side slides on to 2020 aluminum t-slot, while the other side connects to BlueRobotics' 4" enclosure clamp , using 4 M4 screws. As you can see in…
A mount for attaching a GoPro to a flat surface. On the BlueROV2 , the mount attaches to the front of the battery enclosure where it has the same view and lighting as the main camera.
This magical tool helps you change the pesky back o-rings on the BlueROV2 electronics enclosure with ease.
The injection molded model is prone to sagging when the enclosure gets hot. This one has more meat.
This is a mount designed to mount a Recsea GoPro (9, 10, 11) 300m housing and OrcaTorch D560 lasers to the bottom rail of a BlueROV2. GoPro housing is attached using a standard ¼" thumb screw. Lasers are attached using a small hose clamp…
This is a mount for a GPS chip to be mounted to a BlueROV2. The GPS chip can be found on adafruit, screwed into the mount, and encased in epoxy for full 300m depth rating. The GPS chip is intended to run into a Cerulean DVL-75. Our…
