Pug Carlino
My Pug
- Pobrania
- 620
- Polubienia
- 63
- Ocena
- 5
31 modeli
Land Rover Discovery 2 carling switch bracket. There are two version - with or without double-sided adhesive tape. For better fixation use double-sided adhesive tape and "DSBT spring". Frame is bonded by aceton using holes in the body.…
I recreated some classic (JDM-)wheels. They're approximately 1:3 scale and have an diameter of around 13.5cm and a width of around 9cm. They're not a perfect copy as I drew them just after some pictures from the internet. Print them as…
LR D3 Carling switches bracket is situated instead of the ashtray. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Supports: No Resolution: 0.2 Infill: 20 Filament: Any ASA
Puzzle d'un carlin composé de 18 parties, facile à assembler dimensions: 101,5mm x 107mm x 111mm résolution 0,20 remplissage 33% besoin de support
I made this so you can allow the unit to have suffiecient heat dissaptation while mounted via 3M velcro in your car. Suitable for GarlinKit Tbox Ambient AI Box. Print in PETG or ABS/ASA. PLA will melt on a hot day and might damage the…
For the third-gen Tundra's center console. This is for Carling switches, I will add another version for the Toyota smaller push switches as well. Stay tuned. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: Yes Supports:…
A Carlinkit mount for the original phone holder of the Dacia Sandero Stepway. Plug and play. Print it in asa/abs/petg
Мой Carlinkit имеет сильно греется, поэтому установил дополнительный радиатор который мешает прикрепить Carlinkit на двусторонний скотч. две детали необходимо склеить суперклеем, что даст ровную площадку и место под радиатор
Standup Comedians - George Carlin - The Legend 3D printable model.
3 Perimeters Top, Side Bottom 15% Infill 4 Switch Panel https://www.thingiverse.com/thing:3870595 8 Switch Panel https://www.thingiverse.com/thing:4113694 Print Settings Supports: No Resolution: 0.3 **Infill:** 15 Filament: SUNLU PETG…
I purchased a Carlinkit from here a few months ago: https://smile.amazon.com/Carlinkit-Wireless-CarPlay-Compatible-2017-2019/dp/B085VVCLKR/ A couple weeks ago it stopped working. Then I realize that if I moved the cable hard wired into it…
Hello everybody. I needed a holder for my carlinkit wireless adapter to mount inside my glovebox so i made this 3d design. I hope you get good use out of it. I printed it in petg. Have a good one! Category: 3D Printing
3 Perimeters, 3 Top & Bottom layers Holes for #8 Screws 4 Switch Panel https://www.thingiverse.com/thing:3870595 Switch Blank https://www.thingiverse.com/thing:4113263 Print Settings Supports: No Resolution: 0.3 **Infill:** 80 Filament:…
Blue Sea sells panel mounts, but no complete box to house a switch in. This model solves that problem. Just use a drill to flexibly locate a hole in the box or whichever side you want to feed wires into the switch. In the picture, the…
I got tired of accidentally switching off the wrong breakers at night so I created this. This covers the Carling breaker switch on your breaker panel while still being able to see the position. It also lets the breaker trip if needed.…
This is a replacement pre-Td5 Land Rover Defender lower dash switch panel for use with Carling switches. If you prefer not to cut the original factory connectors - I also created adapters for making your own harnesses that plug into the…
This is a holder for the Carlinkit 5.0. I recommend printing in a vertical orientation with the top of the model, where you would slide the device in, facing down. This would have the tab face up. Carlinkit 5.0 Holder © 2024 by Logan…
Carling Switch Removal Tool This makes it easier to remove Carling switches from the rear of a panel. To use, slip it over the back of the switch and push it home flat to release the switch, then use your fingers to push the switch…
This replaces the 2 switch blank switch bank, to fit a single carling type rocker switch in its location.
Scarling 3D print file based off the fan mascot by Scarle Yonaguni https://twitter.com/ScarleYonaguni. Not an official 3D model, just a fanwork by me. They are only allowed for personal use from 3D printers | Not allowed for editing | Not…
This is a template to make cutouts on your dash for Carling switches and all of the import clones. It's spot on in size, so you can adjust your hole accordingly after roughing it in. Print Settings Printer Brand: Creality Printer: Ender 3…
3 Perimeters, 3 Top & Bottom layers Holes for #8 Screws 8 Switch Panel https://www.thingiverse.com/thing:4113694 Switch Blank https://www.thingiverse.com/thing:4113263 Print Settings Printer Brand: Prusa Printer: I3 MK3S **Rafts:** No…
Needed a little enclosure box for the Carling Technologies 622122-BB-NE toggle switch. Has a hole in the rear for wire leads to pass through. https://www.carlingtech.com/sites/default/files/documents/622_632-Series_Details_%26_COS.pdf…
3 Perimeters, top, bottom, side Rocker and Body need to be bonded, recommend Loctite 401 & Hot Glue https://smile.amazon.com/gp/product/B00JFLE196/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Recommend Use of Rocker Switch…
"Greetings, my excellent friends!" Pay tribute to the man who kept the future most non-heinous with this detailed figurine of Rufus. Capturing the iconic likeness of the legendary George Carlin, this model features Rufus in his signature…
Didn't find a propper place to mount my carlinkit, so I've made this holster. It should be fixed in desired place with a 3M tape.
Recommended print settings: Material: PLA or PETG Layer Height: 0.2 mm or less Infill % : 15+ Supports: Yes, Tree/Organic Print Orientation: Default as modeled in STL file The keypad pops in, and the retention features hold it in place.
This is a replica of the logo for "Super Carlin Brothers" a YouTube channel that makes great theory videos on topics like Harry Potter, Marvel, Pixar, Disney, Avatar: The Last Air Bender, Star Wars, and more. Unfortunately, the printer I…
Puzzle d'un carlin composé de 18 parties, facile à assembler dimensions: 101,5mm x 107mm x 111mm résolution 0,20 remplissage 33% besoin de support
This lightbox features the Carling logo, representing the UK's number one beer. Whether for a home bar, pub décor, or just for fans of the iconic brand, this lightbox offers a bold, illuminated display of the classic Carling logo. The…